Supermicro A+ SERVER 1012C-MRF Скачать руководство пользователя страница 96

Страница: 96 / 116

7-4

A+ SERVER 1012C-MRF USER'S MANUAL

GART Error Reporting

This option should remain disabled for normal operation. The driver developer
may enable this option for testing purposes. Options are Enabled or

Disabled

Microcode Update

This setting

Enables

or Disables microcode updating.

Secure Virtual Machine Mode

This setting is used to

Enable

or Disable SVM.

Power Now

This setting is used to

Enable

or Disable the AMD Power Now feature.

Power Cap

This option can decide the highest P-state in the OS. Options include

P-state

through P-state 4.

ACPI SRAT Table

This option

Enables

or Disables the building of the ACPI SRAT Table.

CPU Down Core Mode

This option sets down core support for the CPU. Options include

Disabled

, 1

Core through

Cores in odd numbered increments. The value

is depend on

the core per CPU node.

C1E Support

This option specifies C1E support. Options include

Enabled

and Disabled.

Clock Speed Spectrum

This option enables or

disables

spread spectrum modulation.

Содержание A+ SERVER 1012C-MRF





















































































































Результаты поиска

Содержание A+ SERVER 1012C-MRF

Отзывы:

Похожие инструкции для A+ SERVER 1012C-MRF

Бренды по названию

Популярные бренды

Supermicro A+ SERVER 1012C-MRF, Руководство пользователя

Результаты поиска

Содержание A+ SERVER 1012C-MRF

Отзывы:

Похожие инструкции для A+ SERVER 1012C-MRF

Бренды по названию

Популярные бренды