Supermicro 8028B-C0R4FT Скачать руководство пользователя страница 122

Страница: 122 / 144

7-26

SUPERSERVER 8028B-TR4F/C0R4FT User's Manual

Pending Operation

Use this item to schedule an operation for the security device. The options are

None

Enable Take Ownership, Disable Take Ownership, and TPM Clear.

Note:

The computer will reboot in order to execute the pending commands

and change the state of the security device.

Current Status Information:

This item displays the information regarding the

current TPM status.

TPM Enable Status

This item displays the status of TPM Support to indicate if TPM is currently
enabled or disabled.

TPM Active Status

This item displays the status of TPM Support to indicate if TPM is currently
active or deactivated.

TPM Owner Status

This item displays the status of TPM Ownership.

TXT Support

Select Enabled for Trusted Execution Technology support. The options are Enabled
and

Disabled



ME (Management Engine) Subsystem

This feature displays the following ME Subsystem Con

guration settings.

General ME Con

guration

Operational Firmware Version

Recovery Firmware Version

ME Firmware Features

ME Firmware Status #1

ME Firmware Status #2

Current State

Error Code

Содержание 8028B-C0R4FT

















































































































































Результаты поиска

Содержание 8028B-C0R4FT

Отзывы:

Похожие инструкции для 8028B-C0R4FT

Бренды по названию

Популярные бренды

Supermicro 8028B-C0R4FT, Руководство пользователя

Результаты поиска

Содержание 8028B-C0R4FT

Отзывы:

Похожие инструкции для 8028B-C0R4FT

Бренды по названию

Популярные бренды