Supermicro 8028B-C0R4FT Скачать руководство пользователя страница 102

Страница: 102 / 144

7-6

SUPERSERVER 8028B-TR4F/C0R4FT User's Manual



CPU Confi guration

This submenu displays the following CPU information as detected by the BIOS. It
also allows the user to con

gure CPU settings.



Processor 0/Processor 1/Processor 2/Processor 3

This submenu displays the following information of the CPU installed a CPU socket
detected by the BIOS.

•

Processor Socket

•

Processor ID

•

Processor Frequency

•

Microcode Revision

•

L1 Cache RAM

•

L2 Cache RAM

•

L3 Cache RAM

•

Processor Socket

•

Processor ID

•

Processor Frequency

•

Microcode Revision

•

L1 Cache RAM

•

L2 Cache RAM

•

L3 Cache RAM

•

Processor 0 Version

•

Processor 1 Version

•

Processor 2 Version

•

Processor 3 Version

Clock Spread Spectrum

Select Enable to allow the BIOS to monitor and attempt to reduce the level of
Electromagnetic Interference caused by the components whenever needed. The
options are

Disable

and Enable.

Hyper-Threading (All)

Select Enable to support Intel's Hyper-threading Technology to enhance CPU
performance. The options are

Enable

and Disable.

Содержание 8028B-C0R4FT

















































































































































Результаты поиска

Содержание 8028B-C0R4FT

Отзывы:

Похожие инструкции для 8028B-C0R4FT

Бренды по названию

Популярные бренды

Supermicro 8028B-C0R4FT, Руководство пользователя

Результаты поиска

Содержание 8028B-C0R4FT

Отзывы:

Похожие инструкции для 8028B-C0R4FT

Бренды по названию

Популярные бренды