Supermicro 8028B-C0R4FT Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 144

background image

Chapter 1

Introduction

1-1 Overview

The SuperServer 8028B-TR4F/C0R4FT is a high-end server comprised of two main
subsystems: the SC828TS-R1K43LPB 2U server chassis and the X10QBL-4(CT)
quad processor serverboard. Please refer to our web site for information on operating
systems that have been certi

fi

ed for use with the system (

www.supermicro.com

).

In addition to the serverboard and chassis, various hardware components have been
included with the SuperServer 8028B-TR4F/C0R4FT, as listed below:

•

Four (4) 2U passive CPU heatsinks (SNK-P0048PS)

•

One (1) SC828 air shroud (MCP-310-82806-0B)

•

Three (3) 80x80x38-mm chassis middle fans (FAN-0118L4)

•

SAS/SATA accessories:
One (1) SAS/SATA backplane (BPN-SAS-828TQ-O-P)
Six (6) hot-swap 3.5" hard-disk drive trays (MCP-220-00075-0B)
One (1) Round 30AWG 30" (76-cm) 16-pin to 16-pin ribbon cable
(CBL-0071L)

SuperServer 8028B-C0R4FT only:

Two (2) Mini-SAS HD to 4 SATA, w/75-cm SB cable (CBL-SAST-0556)

SuperServer 8028B-TR4F only:

Two (2) 60-cm 8pin-to-8pin ribbon cables for SGPIO (CBL-0157L-01)
Two (2) 48-cm SATA round S-RA cables (CBL-0227L)
Two (2) 55-cm SATA round S-RA cables (CBL-0228L)
Two (2) 65-cm SATA round S-RA cables (CBL-0230L)

•

One (1) rackmount kit (MCP-290-00053-0N)

Note:

For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

•

Supermicro product manuals:

http://www.supermicro.com/support/manuals/

•

Product drivers and utilities:

ftp://ftp.supermicro.com

•

Product safety information:

http://www.supermicro.com/about/policies/safety_information.cfm

•

If you have any questions, please contact our support team at:

[email protected]

Chapter 1: Introduction

1-1

«
...
9
10
11
12
13
...
»

Содержание 8028B-C0R4FT

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8028B-C0R4FT

Бренд: Panasonic Страницы: 28

eServer 200 xSeries

Бренд: IBM Страницы: 128

eServer 232 xSeries

Бренд: IBM Страницы: 174

System x3100 M4

Бренд: IBM Страницы: 332

Бренд: Sun Fire Страницы: 66

Бренд: TRENDnet Страницы: 14

Бренд: Kontron Страницы: 110

Бренд: Ericsson Страницы: 159

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

Бренд: Gigabyte Страницы: 21

Бренд: Gigabyte Страницы: 143

Бренд: Obvius Страницы: 39

SC835BTQ - R1K28B

Бренд: Supero Страницы: 86

FatTwin F517H6-FT

Бренд: Supero Страницы: 130

Бренд: x-odos Страницы: 58

Yingxin NX 5440

Бренд: Inspur Страницы: 43

Yingxin NF5280M2

Бренд: Inspur Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды