background image

SuperiorFireplaces.us.com

900855-00_B

14

VENTING INSTALLATION 

Continued

Terminations/Spark Arrestor

The fireplace system must be terminated with the listed round top or 

chase terminations. In any case, refer to the installation instructions 

supplied with the termination.

 CAUTION: Do not seal openings on the rooftop 

flashing. Follow the installation instructions provided 

with the termination being used.

Figure 21 - Multiple Chase Installation

Figure 22 - 10 Foot Rule

Figure 20 - Termination

RLT-12D

Level of Flue 

Gas Outlet

Stainless 

Inner Flue 

Pipe

Waterproof 

Caulking

Storm 

Collar

Flashing

Underlap 

Shingles

Overlap Shingles 

(Top and Sides of 

Flashing Base)

Secure 

Termination 

to Outer 

Pipe with 3 

Screws

CHASE INSTALLATIONS

Instructions for chase installations are included with the chase style 

termination chosen. In a multiple chase installation, be sure to provide 

adequate distance between terminations to prevent smoke spillage 

from one termination to another. We suggest that terminations be 

separated at least 24", center to center and stacked at a vertical height 

difference of 18" (see Figure 21).

Note:

 If a decorative shroud is to be installed, contact the manufac-

turer for specifications.

10 FOOT RULE

All flue gas outlet chimney terminations must extend a minimum of 

3 feet in height above the highest point where it passes through the 

roof and must be at least 2 feet above the highest point of the roof 

that is within a horizontal distance of 10 feet (see Figure 22).

10

'

 

(3.05 m)

10

'

 

(3.05 m)

2

'

 (0.61 m) Min.

2

'

 (0.61 m)

 Min.

3

'

 

(0.91 m)

Min

3

'

 

(0.91 m)

Min

Level of Flue 

Gas Outlet

24" (610 mm)

18" (458 mm)

Min. Typ.

24" (610 mm)

SQUARE TOP TERMINATIONS INSTALLATION STL-12D AND 

STL-12DMP

1.  Construct chase as illustrated in Figure 23. 

Note:

 The shortest 

vertical side must be at least 30" high and minimum inside di-

mension must be at least 19" as shown in Figure 23.

2.  Add pipe sections to chimney system as outlined in fireplace 

installation instructions until last piece of chimney is a maximum 

of 6" below top of chase (see Figure 23).

Figure 23 - Constructing Chase

19" 

(483 mm)

6" (153 mm) Max.

30" 

(762 mm) 

Min.

Содержание WRT3538WH

































Отзывы: