background image

Installation 

900636-01, 01/2017

Innovative Hearth Products
DRT4200 Series Direct-Vent Gas Fireplaces

31

6.  Install the firestop/spacer at the ceiling

—When using Secure Vent

®

, use SV4.5VF firestop/spacer at ceiling 

joists; when using Secure Flex

®

, use SF4.5VF firestop/spacer. If there is living space above the ceiling level, 

the firestop/ spacer must be installed on the bottom side of the ceiling. If attic space is above the ceiling, the 

firestop/spacer must be installed on the top side of the joist. Route the vent sections through the framed opening 

and secure the firestop/spacer with 8d nails or other appropriate fasteners at each corner.
Maintain 1” (26 mm) clearance to combustibles, framing members, and attic or ceiling insulation when running 

vertical chimney sections.

7.  Support the vertical run sections

—On the vertical run, support the venting system every 8 ft (2.4 m) above the 

fireplace vent outlet with field provided support straps (Plumber’s tape). Attach the straps to the vent pipe and 

secure to the framing members with nails or screws 

(

Figure 21, Page 26

)

.

8.  Change vent direction

—At transition from or to a horizontal/inclined run, install SV4.5E45 or SV4.5E90 elbows 

in the same manner as the straight vent sections. The elbows feature a twist section to allow them to be routed 

about the center axis of their initial collar section to align with the required direction of the next vent run element. 

Twist elbow sections in a clockwise direction only so as to avoid the possibility of unlocking any of the previously 

connected vent sections 

(

Figure 17

)

.

9.  Continue installation of horizontal/inclined sections

—Continue with the installation of the straight vent 

sections in horizontal/inclined run. Install support straps every 5 ft. (1.52 m) along horizontal/inclined vent 

runs using conventional plumber’s tape 

(

Figure 25

)

. Maintain the horizontal/inclined run in a straight (no dips), 

slightly elevated plane. The recommended incline is approximately 1/4” per 1 ft (20 mm per 1 m) horizontal, in 

a direction away from the fireplace. 

Smaller rise per foot run ratios are acceptable all the way to at or near 

level.

 Use a carpenter’s level to measure from a constant surface and adjust the support straps as necessary. 

Maintain the required clearances to combustibles

 (

Page 30

)

.

10. Assemble the vent run to the exterior wall

—If not previously measured, locate the center of the vent at the 

exterior wall. Prepare the opening. Assemble the vent system until the terminus of the last section is within 

7” (178 mm) to 11-1/4” (286 mm) inboard of the exterior surface to which the SV4.5HT termination is to be 

attached 

(

Figure 26

)

. If the terminus of the last section is not within this distance, use the telescopic vent section 

SV4.5LA, as the last vent section. 

Table 20

 lists the additional venting components needed (in addition to the 

termination and adaptor) for a range of wall thicknesses.

11. Attach the termination adaptor

—Attach the adaptor (SV4.5RCH, provided with the termination) to the vent 

section or telescoping vent section, elbow or fireplace collar 

(

Figure 26

)

.

12. Install the firestop/spacer at the exterior wall

—When using the square termination, install SV4.5HF (Secure 

Vent), SF4.5HF (Secure Flex) Firestop/Spacer over the opening at the exterior side of the framing, long side up, 

with the 3” spacer clearance at the top 

(

Figure 26

)

 and nail into place. 

NOTE: 

The firestop/spacer may also be installed over the opening at the interior side of the framing.

13. Install the termination (

SV4.5HT-2

)

—From outside the exterior wall, slide the collars of the termination onto the 

adaptor (the outer over the outer and the inner inside the inner) until the termination seats against the exterior 

wall surface to which it will be attached. Orient the housing of the termination with the arrow pointed upwards. 

Secure the termination to the exterior wall. The horizontal termination must not be recessed into the exterior wall 

or siding by more than the 1-1/4” (32 mm) 

(

Figure 27

)

.

NOTE: 

If the venting exits the building below grade, or close to grade, see 

Installation Accessories on 

Page 47

 

for available snorkel terminations. The termination must be above grade and above the expected level of 

snow accumulation.

NOTE: 

The vent termination is hot while in operation and for a period of time following the use of the fireplace. 

To prevent contact with hot surfaces, use a horizontal termination guard; available for purchase at your local 

dealer.

The horizontal terminations have been designed to perform in a wide range of weather conditions. Our 

terminations meet or exceed industry standards.
When selecting the locations of your horizontal terminations, 

do not place the termination where water from 

eaves and adjoining rooflines may create a heavy flow of cascading water onto the termination cap

. If the cap 

must be placed where the possibility of cascading water exists, it is the responsibility of the builder to direct the 

water away from the termination cap by using gutters or other means.
Take care to carefully follow the installation instructions for the termination, including the use of silicone caulking 

where required.

Содержание DRT4200 Series







































































Отзывы: