manualshive.com logo in svg

Superior Fireplaces DRT4200 Series, Инструкция по установке и эксплуатации, Страница: 20 / 70

Поделиться
Скачать
Superior Fireplaces DRT4200 Series Скачать руководство пользователя страница 20

Installation 

900636-01, 01/2017

Innovative Hearth Products
DRT4200 Series Direct-Vent Gas Fireplaces

20

Step 1: 

Remove the eight (8) screws 

holding the top vent cover plate and 

gasket.

Step 4

: Make sure insulation disc is 

still in the round cover. Remove the 

flue plug from the top flue.

Step 5

: Bend tabs out on round 

flue cover. 

Step 6

: Secure the round flue cover (provided) 

to the wrapper over the rear venting outlet. 

Use two (2) 3/4” long sheet metal screws 

Separate and note metal side (2) 

and center (1) brackets.

Step 1: 

Remove two screws from the top and side of the unit. Bend the side bracket securing tab over the 

edge of the unit and secure. Secure bracket to the top through the clearance screw hole.

Step 2: 

Remove the three screws that align with the clearance screw 

holes from the top of the unit. Secure the center bracket to the top 

center of the fireplace

Step 3: 

Top of front fireboard 

standoff should be flush with 

top standoffs (not shown).

Step 4:

 Fireboard standoff can 

be secured to the capture screw 

holes.

4. 

Determining Vent Setup in the Combination Venting Unit* 

Combination venting units are shipped with rear venting setup nearly ready for install. If this is the type of vent you require, remove 
all insulation packing and flue plug block off from rear venting  and proceed with fireplace installation.

If you require a top-vented unit, use the following steps to convert the fireplace before use.

Step 2

: Remove the round flue cover 

from the top venting outlet.

Step 3

: Remove insulation from 

inside flue pipe.

5. 

Installing Non-Combustible Front Fireboard Standoff 

A non-combustible standoff board is provided with the fireplace to prevent overlap of drywall or other material of portions of the fireplace that may 

be prone to the buildup of heat. It is supported by a middle bracket and two side brackets.

* 45” Models are Top Vent Only.

Step 7.

 Remove the 2 screws 

holding the block off plate and 

gasket to top vent flue. Retain 

screws as they will be re-used.

Step 8. 

Remove the 4 screws 

around the rear vent and use to 

Re-install block off plate and gasket 

over the rear vent flue.

Содержание DRT4200 Series







































































Отзывы:

Нет отзывов