Super B Epsilon SB12V1200Wh-M Скачать руководство пользователя страница 36

Страница: 36 / 50

10. Troubleshooting

Problem

Possible situation

Solution

The battery

cannot be

discharged.

Battery is in normal mode Green LED is

lit or flashing. (Chapter 2.7.10)

Check the installation of the battery.

Battery is in shutdown mode.

No LED is lit or flashing (Chapter 2.7.10)

Charge the battery or Press the S1

Push button for 2 seconds.

Battery is in degrade mode

Red LED is lit or flashing. (Chapter

2.7.10)

Charge the battery.

The battery

cannot be

charged.

Battery is in normal mode Green LED is

lit or flashing.(Chapter 2.7.10)

Check the installation of the battery.

Battery is in degrade mode

Red LED is lit or flashing. (Chapter

2.7.10)

Discharge the battery.

The capacity of

the battery has

decreased.

The cells within the batteries are not

properly balanced, causing them to

discharge at different rates.

Perform one full charge cycle to

balance the cells.

Green and

Yellow LED is lit

or flashing

Battery in Warning mode (Chapter

2.7.10)

State of charge is low, fully charge the

battery

Cable assembly

does not fit

underneath

standard battery

cover (handles).

The connectors you are using are too

big.

Use other smaller connectors or

remove the handles and use the

automotive type of covers.

Table 20. Troubleshooting

Содержание Epsilon SB12V1200Wh-M



















































Результаты поиска

Содержание Epsilon SB12V1200Wh-M

Отзывы:

Похожие инструкции для Epsilon SB12V1200Wh-M

Бренды по названию

Популярные бренды

Super B Epsilon SB12V1200Wh-M, Руководство пользователя

Результаты поиска

Содержание Epsilon SB12V1200Wh-M

Отзывы:

Похожие инструкции для Epsilon SB12V1200Wh-M

Бренды по названию

Популярные бренды