SUNWARD SWE215F-5 Скачать руководство пользователя страница 46

Страница: 46 / 182

OPERATION & MAINTENANCE MANUAL SWE215F

2.1.3 Loading or Unloading with a Trailer

Warning



When loading or unloading, do not go at idle

speed mode to prevent sudden change in speed.



Set travel speed at low position. Do not attempt

any travel speed switching operation to avoid that

sharp change of speed and over-speed cause danger.

Always keep the machine travel at low speed.



Be sure engine runs at low speed, adjust

throttling knob to keep the engine run at low speed.



When loading or unloading, do not attempt any

steering operation. At which moment, steering

operation is extremely dangerous. The machine is

subject to rolling over. If the machine needs to

change direction, go back to level ground or trailer

platform, then revise travel direction and cross the

slope.



Do not attempt any other operations (e.g.

steering and moving work equipment etc) on slope.

Allow only travel operation.



Because it

’

s a raised shape at the place where

ramp intersects the flats. Pay attention to pass it:

the slope should not exceed 15



Prevent the machine from tipping over and

other damages due to upper-structure slewing.

Lower the boom, fold arm and bucket and slew the

upper-structure slowly to get the optimum stability.



Clean up the track, slope of the trailer and

loading surface to prevent hazards resulting from

obstacle and oil

Содержание SWE215F-5























































































































































































Результаты поиска

Содержание SWE215F-5

Отзывы:

Похожие инструкции для SWE215F-5

Бренды по названию

Популярные бренды

SUNWARD SWE215F-5, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SWE215F-5

Отзывы:

Похожие инструкции для SWE215F-5

Бренды по названию

Популярные бренды