background image

iii

afety Information

s

LABELING NOTICE:

Labels are affixed on all systems to inform the user of possible dangers. Regulations are stated in

21 CFR, Section 1040.20, and require that all products manufactured after September 8, 1986 which use sunlamps
must display the following:

Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexpo-
sure can cause eye and skin injury and allergic reactions. Repeated exposure may cause pre-

mature aging of the skin and skin cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS
OR LONGTERM INJURY TO THE EYES.

Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using
sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to
sunlight. If you do not tan in the sun, you are unlikely to tan from the use of this product.

Minimum use distance from face tanner is 1 inch or 2.54 centimeters. Minimum use distance elsewhere is touching
the clear plastic panels. Do not use without clear plastic panels (or wire grid for models using wire grid) in place.
Tanning normally appears after the first few sessions and maximizes after approximately four weeks. Tan once or
twice per week thereafter to maintain appearance. Frequency of sessions should be limited to every other day.
Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan.

New lamps emit approximately 20% more UV during the first 50 hours of operation. Recommended tanning times
should therefore be reduced by approximately 20% during that period.

WARNING:  

• Read the instructions booklet before using this sunlamp product. • To use, lie down under canopy

and pull down as far as adjustment will allow. All persons in the room should wear protective eyewear when lamps
are on. • Recommended eyewear: provided eyeshields (Lucas Products Super Sunnies or Intrexco No. 5635/1) or
equivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear may not provide adequate protec-
tion. • Disconnect power cord before attempting to clean, relamp, or engage in the maintenance of this product.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RS MODEL SERIES:

Velocity

TM

Wolff

®

Model 71T12100W

24RS

Diamond Sun

®

S Wolff

®

Model 71T12100W

24RS and 26RS

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RSF MODEL SERIES:

Velocity

TM

Wolff

®

Model 71T12100W & Model 59T12080W

24RSF

Diamond Sun

®

S Wolff

®

Model 71T12100W & Model 59T12080W

24RSF 

Philips Model HPA 400/30s or CosmoTech Model 23045 or CosmoTech 20046 (Facial Unit)      24 RSF  

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RST MODEL SERIES:

Velocity

TM

Wolff

®

Model 71T12100W

24RST

Diamond Sun

®

S Wolff

®

Model 71T12100W

24RST and 26RST

Turbo Sun

TM

S Wolff

®

Model F8-T5-10W

24RST and 26RST

THIS EQUIPMENT MUST BE CONNECTED TO A GROUNDED OUTLET.
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER 21 CFR 
PART 1040.20 

DANGER

RECOMMENDED EXPOSURE TIMES IN MINUTES                 MAXIMUM EXPOSURE TIME IS 20 MINUTES

Skin Type:

Week #

Week 1

Week 2

Week 3

Week 4

Subsequent

Session #

1st-3rd 

4th-6th

7th-10th

11th-13th

Maximum

I   

Sensitive Skin (Burns easily and severely and does not tan.)

NOT RECOMMENDED FOR TANNING

II  

Light

(Burns easily and severely and tans minimally.)

4

8

12

16

20

III

Normal

(Burns moderately and tans average.)

6

10

15

20

20

IV

Dark

(Burns minimally, tans easily and above average.)

8

12

16

20

20

Содержание PRO 24RS
























Отзывы: