Sungrow SG285HX Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 128

background image

74

•

If there is one wire per phase, with multi-core cable, the maximum communication dis-

tance is 1000 m.

•

If there are two wires per phase, with multi-core cable, the maximum communication dis-

tance is 1000 m. The distance between two AC cables should be more than 15 cm. The
length of the two AC cables should be the same. If not, the length difference must be
smaller than 2m.

•

The Data Logger is an optional device that can be ordered from SUNGROW.

•

The Data Logger conducts data communication by directly using the AC output
cable of the inverter and thus saves the trouble to lay and maintain the special
communication cables. The RS-485 port of the Data Logger supports the
transparent transmission of the MODBUS-RTU and is completely compatible
with the monitoring devices and software of the original RS-485 communica-
tion method.

5 Electrical Connection

User Manual

«
...
82
83
84
85
86
...
»

Содержание SG285HX

































































































































Отзывы:

Нет отзывов

Похожие инструкции для SG285HX

Бренд: Kramer Страницы: 14

Бренд: Rohde & Schwarz Страницы: 95

EAL580 MT Series

Бренд: Baumer Страницы: 74

UNIRAC POLETOPS 5000 Series

Бренд: Hilti Страницы: 4

AIS Splitter 100

Бренд: Raymarine Страницы: 24

Бренд: Mase Страницы: 22

Automotive Ethernet Converter

Бренд: X2E Страницы: 22

Бренд: Kramer Страницы: 15

Бренд: PEAK COMMUNICATIONS Страницы: 18

Бренд: D&R Страницы: 17

Бренд: Baumer Страницы: 36

Бренд: MPP Solar Страницы: 4

FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR

Бренд: Fuji Electric Страницы: 263

Бренд: B&B Electronics Страницы: 2

Бренд: Digitus Страницы: 4

Бренд: Goobay Страницы: 4

Бренд: Hoymiles Страницы: 2

Бренд: Microchip Technology Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды