6
7
A
TTACHING THE
B
EATERS
Be sure the speed control dial is in the
OFF position and unplug electric cord
from the electrical outlet.
Lift mixer head up and back to pull it
out of the way of the bowl.
N
OTE
:
It is important that the beaters
go into the correct sockets. Otherwise
the mixer will not give you the proper
mixing action. Do not risk ruining a
recipe or damaging your mixer. Read
the following instructions carefully.
One of the beaters is shaped like a cone
and has a nylon button on the bottom.
It goes into the socket on the side of
the mixer nearest the side of the bowl.
The other beater is square-shaped and
goes into the socket nearest the center
of the bowl. See beater symbols located
on the bottom of the mixer head.
Insert the beaters, one at a time,
using a combination pressing and
twisting motion, until the beaters
snap into position.
If a beater should not properly snap
into place, pull it out of the socket
and rotate it one quarter turn.
Reinsert the beater into the socket
until it snaps into position.
A
TTACHING THE
D
OUGH
H
OOKS
(Some Models Only)
Set the speed dial in the OFF position
and unplug the electric cord from the
electrical outlet.
Lift mixer head up and back to tilt it out
of the way of the bowl, while holding it
in an upright position.
N
OTE
:
The dough hooks must go into
the correct sockets. The mixer will
operate with the dough hooks in the
wrong position. However, you will not
get proper kneading action and you
could risk ruining a recipe or damaging
your mixer. Read the following
instructions carefully.
N
YLON
B
UTTON
S
QUARE
B
EATER
C
ONE
-S
HAPED
B
EATER
S
IDE OF
B
OWL
C
ONE
B
EATER
S
QUARE
B
EATER
The dough hook with the small washer
and foot goes into the socket on the
side of the mixer nearest the side of
the bowl. The other dough hook with
the large washer goes into the socket
nearest the center of the bowl. See the
dough hook symbols located on the
bottom of the mixer head.
B
EATER
-B
OWL
D
RIVE
A
DJUSTMENT
Automatic bowl rotation is factory set.
Occasionally, a simple adjustment
may be necessary when the bowl
fails to rotate.
To make this adjustment, tilt the mixer
head back. Hold the mixer head in an
upright position and locate the
adjustment screw on the underside
of the mixer head. Loosen the locking
nut and turn the adjustment screw on
the underside of the mixer head.
Loosen the locking nut and turn the
adjustment screw clockwise, to lower
the mixer head; or counter clockwise,
to raise the mixer head. Retighten the
locking nut. The beater with the nylon
button should lightly touch the bottom
of the mixing bowl.
O
PERATING
I
NSTRUCTIONS
A
BOUT THE
S
PEED
C
ONTROL
D
IAL
The speed control dial is used
for turning the mixer ON and OFF
and for selecting its 12 mixing speeds.
Rotate the speed control dial in a
clockwise direction to increase mixing
speed; and in a counter-clockwise
direction to decrease mixing speed.
As you rotate the speed control dial,
notice that a numbered speed
is aligned with the indicator on top
of the mixer head. This numbered
speed indicates the speed at which
the mixer is operating.
Rotate the speed control dial until
the indicator is opposite the numbered
speed you wish to use.
B
URST OF
P
OWER
® F
EATURE
Press down on button or top handle to
automatically increase the beater speed
by 150 RPM for an immediate boost
of power.
H
EAD
L
OCK
The head lock feature locks the mixing
head in the down position for added
control while mixing and locks it in the
up position for added convenience
while cleaning. To unlock, press down
the button on the side of the stand.
To lock, lower mixing head until it
automatically locks in place.
S
PEED
I
NDICATOR
M
IXING
G
UIDE
S
PEED
C
ONTROL
D
IAL
A
DJUSTMENT
S
CREW
L
OCKING
N
UT