Sun Microsystems Sun Netra CP3220 Скачать руководство пользователя

Страница: 65 / 135

Chapter 2

Hardware Installation and Service

2-31

To reset the jumper and return the CMOS settings to the default settings, perform
the following steps:

1. Remove the jumper housing from the run position (P1/P2) and move it to the

reset position (P2/P3).

FIGURE 2-11

Jumper 1 in the Reset Position

2. Wait at least one second for the CMOS settings to reset and then move the

jumper housing back to the run position.

3. Reinstall the blade server.

Use the procedure in

Section 2.2.3.2, “Installing the Blade Server Into the Shelf”

on page 2-12

Note –

The blade server will operate normally only when the jumper housing is in

the run position.

Jumper 1

Pin 1
Pin 2
Pin 3

Zone 3

AMC slot B1

Zone 3

connectors

Содержание Sun Netra CP3220








































































































































Результаты поиска

Содержание Sun Netra CP3220

Отзывы:

Похожие инструкции для Sun Netra CP3220

Бренды по названию

Популярные бренды

Sun Microsystems Sun Netra CP3220, Руководство пользователя

Результаты поиска

Содержание Sun Netra CP3220

Отзывы:

Похожие инструкции для Sun Netra CP3220

Бренды по названию

Популярные бренды