Sun Microsystems Sun Netra CP3220 Скачать руководство пользователя | Manualshive

Страница: 80 / 135

background image

4-2

Sun Netra CP3220 Blade Server User’s Guide • January 2010

4.1

About BIOS Settings

This section describes how to view and modify the BIOS settings.

The BIOS has a Setup utility stored in the BIOS flash memory. The Setup utility
reports system information and can be used to configure the BIOS settings. The
configured data is provided with context-sensitive help and is stored in the system's
battery-backed CMOS RAM. If the configuration stored in the CMOS RAM is
invalid, the

BIOS settings will default to the original state specified at the factory

.

4.1.1

Navigating BIOS Screens

The BIOS Setup utility contains seven menu screens, which are displayed in this
order: Main, Advanced, PCI/PnP, Boot, Security, Chipset, and Exit. See

Appendix B

for a BIOS menu tree and illustrations of the screens.

Use the left and right arrow keys to move sequentially through the seven BIOS
screens. Fields that can be reconfigured are displayed in color. All other fields are
non-configurable. Use the up and down arrow keys to scroll through a screen's
menu. Use the Tab key to move across columns.

4.1.2

BIOS Considerations

This section contains special considerations regarding the system BIOS.

4.1.2.1

BIOS Option ROMs on the Sun Netra CP3220 Blade Server

The Sun Netra CP3220 blade server has an option ROM for each of the following
components:

■

Broadcom BCM 5715C base interfaces

■

MPC55 Ethernet administration interfaces

■

Sun 10 GbE Multithreaded Networking ASIC Extended fabric interfaces

«
...
78
79
80
81
82
...
»

Содержание Sun Netra CP3220








































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sun Netra CP3220

FrameSaver SLV 9126

Бренд: Paradyne Страницы: 24

Бренд: ACTi Страницы: 11

Бренд: Fujitsu Страницы: 44

PRIMERGY RX900 S2

Бренд: Fujitsu Страницы: 114

PRIMERGY RX800 S2

Бренд: Fujitsu Страницы: 66

Бренд: Fujitsu Страницы: 8

Бренд: Fujitsu Страницы: 99

PRIMERGY SX05 S1

Бренд: Fujitsu Страницы: 52

PRIMERGY RX600 S5

Бренд: Fujitsu Страницы: 82

PRIMERGY ServerView Suite

Бренд: Fujitsu Страницы: 62

PRIMERGY RX800 S2

Бренд: Fujitsu Страницы: 149

PRIMERGY RX600 S6

Бренд: Fujitsu Страницы: 134

PRIMERGY RX600 S6

Бренд: Fujitsu Страницы: 62

Primergy RX600 S2

Бренд: Fujitsu Страницы: 121

PRIMERGY RX500 S7

Бренд: Fujitsu Страницы: 88

PRIMERGY RX600 S3

Бренд: Fujitsu Страницы: 305

PRIMERGY RX600 S3

Бренд: Fujitsu Страницы: 119

PRIMERGY RX600 S5

Бренд: Fujitsu Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды