manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 55

Chapter 5

 SAN 

Configurations 

 

39

9. Map Logical Drive 1 to channels 1 and 5 of the secondary controller.

10. If more than two logical drives were created, map even-numbered logical drives to 

channels 0 and 4 of the primary controller and odd-numbered logical drives to 
channels 1 and 5 of the secondary controller.

11. Connect the first switch to port FC 0 of the upper controller and port FC 1 of the 

lower controller.

12. Connect the second switch to port FC4 of the lower controller and port FC5 of the 

upper controller.

13. Connect each server to each switch.

14. Install and enable multipathing software on each connected server.

15. After completing the configuration, save the configuration using the “Save nvram 

to disks” menu option in the firmware application or the “save configuration” 
option in Sun StorEdge Configuration Service.

Redundant Point-to-Point SAN 
Configurations

FIGURE

 

5-4 

Sample Redundant Point-to-Point SAN Configuration

 

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды