manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 21

Chapter 1

 Introduction 

 

5

■

Information lifecycle management

■

Content addressable storage

■

Backup and restore

■

Secondary SAN storage

■

Near-line DAS storage

■

Static reference data storage

Note – 

Procedures described for configuring Sun StorEdge 3510 FC arrays and Sun 

StorEdge 3511 SATA arrays are the same except where noted in this manual.

Sun StorEdge 3511 SATA expansion units can be connected to Sun StorEdge 3510 FC 
arrays, either alone or in combination with Sun StorEdge 3510 FC expansion units. 
Up to five expansion units can be used in this configuration. For instance, you might 
wish to use the Fibre Channel drives for primary online applications and the SATA 
drives for secondary or near-line applications within the same RAID array. For an 
example of such a configuration, see 

“Combining Sun StorEdge 3510 FC Arrays and 

Sun StorEdge 3511 SATA Expansion Units” on page

 

67

.

Sun StorEdge 3510 FC arrays use Fibre Channel (FC) disk drives, and are supported 
by Sun Microsystems in primary online applications as well as secondary and near-
line applications. Sun StorEdge 3511 SATA arrays are supported by Sun 
Microsystems in either near-line applications, such as backing up and restoring data, 
or secondary applications such as static storage. Sun StorEdge 3510 FC arrays can be 
used in multipath and multi-host configurations, but they are not designed to be 
used in primary online applications or as boot devices.

Caution – 

Although the two products are very similar in appearance and setup, the 

configurations have very important differences. While the Sun StorEdge 3510 FC 
array can be used for all applications, the Sun StorEdge 3511 SATA array cannot, and 
inappropriate use in applications for which the Sun StorEdge 3510 FC array was 
designed may result in the loss of data and/or data access.

Refer to the Installation, Operation, and Service manual for your array for more 
detailed information about differences between Sun StorEdge 3510 FC arrays and 
Sun StorEdge 3511 SATA arrays. Refer to the release notes for your array for 
information about additional disk capacities that may be available for your array.

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды