manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 41

25

C H A P T E R

4

DAS Configurations

This chapter presents several DAS configurations you can use.

Single-Controller DAS Configurations

Note – 

Using single connections between Fibre Channel arrays and servers creates 

single points of failure (SPOF) that can cause interruptions in the event a connection 
becomes unreliable or fails. This is not a recommended configuration unless host-
based mirroring is utilized to protect against single points of failure. Similarly, using 
only a single controller creates a single point of failure, unless single controllers are 
used in pairs and mirrored. Using a dual-controller configuration, as shown in 

“Dual-Controller Multipath DAS Configurations” on page

 

29

, is preferable to using a 

single controller or a pair of single controllers.

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды