A. TO EXTEND OR COLLAPSE THE LEGS
The legs are made to easily retract into the fire pit for
transport and storage. The unit will be shipped with all
legs in the collapsed position. Each leg has a “leg locking
button” that engages in the fire pit sidewalls to secure into
place. Before assembling or operating the fire pit, depress
the button and pivot each leg to the extended position as
shown in Figure A. Reverse the process to collapse the
legs before transporting or storing the fire pit
.
1.
Remove packing material and all parts from the carton.
Packing material and carton can be retained for storage if
desired.
2.
Refer to the parts list on page 3. Ensure that all
components are contained in the package.
3.
Align the Control Valve Knob with the Control Valve Shaft
and press fully into place.
4.
Push in and rotate the Control Valve Knob counter
clockwise . You should hear a click of the ignitor at the
90° mark. This will be the
HIGH setting
. Rotate the knob
to the 180° mark. This will be the
LOW setting
.
5.
Ensure legs are in the extended position as shown
in Figure A above. Install the collection pan (110860)
and spacer (063863) using the Bolt (122153) and Nut
(122154) supplied. Tighten bolt until pan is snug.
6.
Remove the Pumice Stone from the plastic packaging
and place the stone on top of the burner uniformly to fill
the pan. Burn media must cover the complete burner by
a minimum of one (1) inch to assure proper performance
and operation. Do not operate unit until the correct
amount of media is present. Do not place any combustible
material in the burner pan. Only use Suburban approved
burner media
.
4
LEG LOCKING CATCH
A
IMPORTANT
Review these instructions prior to
assembly.
ASSEMBLY
Review these instructions prior to the
assembly of your appliance. Please refer
to page 5 for illustrations.
7.
Using a Phillips screw driver, install the lid handle onto
the storage lid using the screws and washers provided.
Tighten securely. Do not overtighten.
8.
Place the lid on the unit ensuring the tabs on the lid
align with the large openings in the top. Rotate counter
clockwise to lock the lid in position. Never place the lid
on the appliance while it is in operation or still hot from
use.
WARNING
9.
Place the portable LP gas cylinder (not included) at a
minimum distance of 60” (5 ft) from the appliance. Ensure
the cylinder is on a solid surface and protected from tipping
and moisture. Anti-tip device must be used at all times.
10.
Attach the Swivel Nut attached to the LP gas regulator
on the outlet of the cylinder. Hand tighten the nut on the
fitting - do not use tools to connect. The LP gas regulator
should be protected from moisture at all times.
11.
A hose retainer is located on the front leg of the appliance.
Place the hose in the opening. Ensure hose and cylinder
are out of any pathway and not in danger of being
accidentally damaged.
12.
To leak test the system, turn the unit control valve to
the “off” position. Brush a soap and water mixture on all
connections. Turn the gas supply on; if bubbles occur on
any connection there may be a leak. If you smell gas or
a leak is discovered turn the gas valve off, disconnect
propane gas tank and do not use the appliance until the
leak is repaired.
13.
Review all warning labels on the appliance. Some labels
may be located on the back side of the appliance.
14.
Set the propane bottle into the anti-tip ring and secure the
ring to the bottle by hand tightening the supplied thumb
screw.
LIGHTING AND SHUTDOWN INSTRUCTIONS
Read and become familiar with all WARNINGS and
instructions in this manual, on the appliance and on the
LP gas cylinder before lighting this appliance. Failure to
do so may result in personal injury, property or death.
WARNING
1.
Ensure the portable LP gas cylinder is at minimum 60”
(5 ft) from the appliance and the gas hose is not in a
pathway that could cause a trip hazard
2.
Ensure there are no combustible materials, liquids
or vapors in the vicinity of the appliance. Ensure the
appliance is away from all walls and ceilings.
3.
The control valve knob should be in the
OFF
position.
4.
Remove the lid from the appliance by pressing the release
button and rotating clockwise . Store in a safe location
when not in use.
5.
Turn the LP gas cylinder on fully by rotating the knob on
top of the cylinder counter clockwise .
OPERATION
Review these instrucitons prior to the
operation of your appliance.
