background image

Index

01

Index

Features

LED Indication.

8

Parameter List.

To set the quick freeze set point.

QFS

9

Key Introduction

6

4

Fault Messages.

7

DESCRIPTION

PARAMETER

Pg. 
No. 

To set the cut-out point of the controller.

SET POINT

9

To set other parameter

9

To set allowable high temperature limit. 

To set allowable low temperature limit.

To set the differential for compressor 
restart. 

P2 

P3

P4

10

10

10

To set  probe calibration.

P5

11

To  set  time  delay  between  relay  restart 
time.

P6

11

To set duration of defrost.

P7

12

To set defrost frequency.

To set power on defrost delay.

To set type of defrost.

To set  drip time for defrost.

To set defrost stop temperature.

To set type of computation for defrost time.

P8

P9

P10

P11

P13

P12

12

12

13

13

14

13

14

14

Items Included.

5

9

EXIT

End of set mode

9

DI-D

To select AUX or compressor thermal 
trip digital I/P

OPS

To Enable / Disable Oil Pressure Switch 
(OPS) I/P.

Index

02

Index

DESCRIPTION

PARAMETER

Pg. 
No. 

To set Evaporator Fan stop temperature.

To set Evaporator Restart Delay.

To set Evaporator Fan status at 
compressor off.

To set Evaporator Fan differential.

To set Evaporator probe calibration.

15

To set condenser status at hot gas 
defrost.

CND7

L1

L2

L3

L4

L5

16

16

16

17

17

17

17

18

19

19

20

To set Evaporator Fan status at Door 
open condition.

L7

20

To enable / disable buzzer.

BUZ

21

Alarm Relay Enable / Disable.

AL

21

Under load limit for compressor current.

C-UL

21

Over load limit for compressor current.

C-OL

22

To  set Evap Fan status during defrost.

L8

20

To set  reset mode for HP fault.

D4

To set Compressor Relay status on 
Probe Failure.

E1

Current sensing delay.

C2

To enable or Disable HP sensing. 

D0

To enable or disable LP sensing.

D1

Fault sensing logic.

To set LP sensing delay.

D2

D3

16

15

To set quick freeze duration.

QFD

15

To set condenser on delay time.

CND6

18

HT Power ON alarm delay.

ADT

18

Alarm/Buzzer output delay at Door open

ADD

18-19

Temperature Hold Duration at Door open

THD

Содержание CRC-2052























Отзывы: