Sub-Zero 600-2 Series Скачать руководство пользователя страница 31

Страница: 31 / 63

Page 31

7-31

Built-In

(600-

)

Series

Component Access / Removal

#3758407 - Revision B - August, 2006

Figure 7-75. Upper Basket Full Extension Slide

Figure 7-76. Freezer Drawer Slide Rail

Figure 7-77. Full Extension Drawer Slide Assy.

Upper Basket Slide

Drawer Slide

Drawer Slide Rail

Freezer Cabinet Slide Assembly

(611-2/611G-2,650-2/650G-2 Prior to Serial #2354455)

The freezer cabinet slides are attached to the side wall
with screws.

To remove a cabinet slide assembly, extract the mount-
ing screws and pull it from the side wall

(See Figure 7-

74).

Upper Freezer Basket Full Extension Slide

(611-2/611G-2,650-2/650G-2 Start w/Serial #2354455)

The upper freezer basket full extension slides are
attached to the side walls of the freezer with screws.

To remove an upper freezer basket full extension slide,
first remove the drawer front assembly and both freezer
baskets, then extract the slide mounting screws and pull
the slide from the side wall.

(See Figure 7-75)

Freezer Drawer Slide Rail Assembly

(611-2/611G-2,650-2/650G-2 Start w/Serial #2354455)

The drawer slide rail assemblies are attached to the full
extension drawer slides with screws.

To remove a drawer slide rail assembly, first remove the
drawer front assembly and the lower freezer basket,
then

(See Figure 7-76):

Extend slide rail out fully.

Extract slide rail mounting screws, then lift slide rail
from the slide.

Freezer Full Extension Drawer Slide Assembly

(611-2/611G-2,650-2/650G-2 Start w/Serial #2354455)

The full extension drawer slide assemblies are attached
to the side walls with screws.

To remove a full extension drawer slide assembly, first
remove the drawer front assembly, lower freezer basket
and drawer slide rail assembly, then

(See Figure 7-77):

Extend drawer slide until front access hole lines up
with front mounting screw.

Extract slide mounting screws, then pull slide from
the side wall.

Figure 7-74. Freezer Cabinet Slide

Prior to Serial

#2354455

Freezer Cabinet Slide

Starting w/Serial

#2354455

Starting w/Serial

#2354455

Starting w/Serial

#2354455

Содержание 600-2 Series
































































Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды

Sub-Zero 600-2 Series, Руководство по обслуживанию

Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды