Sub-Zero 600-2 Series Скачать руководство пользователя страница 42

Страница: 42 / 63

Page 42

7-42

Component Access / Removal

Built-In

(600-

)

Series

#3758407 - Revision B - August, 2006

Figure 7-109. Juice Can Rack

Lift
up.

Pull
out.

FREEZER INTERIOR COSMETIC / MECHANICAL (MODELS 685-2 -

prior to serial #2271174

, 695-2 -

prior to

serial #2269189

)

NOTE:

Also see “FREEZER INTERIOR COSMETIC / MECHANICAL (MODELS 685-2 - starting with serial

#2271174, 695-2 - starting with serial #2269189), later in this section.

Freezer Door Shelf Assembly Removal / Adjustment
(685-2, 695-2)

Removal and adjustment of door shelf assemblies is
achieved by sliding the grooves in the end caps over
the molded retaining ribs of the door liner.

Lift up and out to remove, push in and down to install

(See Figure 7-107).

Freezer Compartment Shelf Removal / Adjustment
(685-2, 695-2)

Remove and adjust shelf by tilting up at front while lift-
ing the back up and out of the shelf ladders

(See Figure

7-108).

To reinstall, tilt front of shelf up and align hooks at back
corners with slots in shelf ladders, then insert hooks
into slots and lower front of shelf.

Juice Can Rack Assembly (685-2, 695-2)

Hooks at the back of the juice can rack assembly fit into
slots in the evaporator front cover.

To remove juice can rack assembly

(See Figure 7-109):

Lift rack up.

Pull rack forward.

Figure 7-107. Door Shelf

Figure 7-108. Compartment Shelf

Shelf Ladders

Shelf

Содержание 600-2 Series
































































Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды

Sub-Zero 600-2 Series, Руководство по обслуживанию

Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды