Sub-Zero 600-2 Series Скачать руководство пользователя страница 40

Страница: 40 / 63

Page 40

7-40

Component Access / Removal

Built-In

(600-

)

Series

#3758407 - Revision B - August, 2006

Defrost Terminator (632-2, 642-2, 661-2)

The defrost terminator is clipped onto the evaporator
outlet, after the accumulator.

To remove the defrost terminator, remove the freezer
shelves, ice bucket and duct/shelf assembly first, then

(See Figures 7-101):

Disconnect terminator wire leads from wire harness.

Pull terminator off of tubing.

Freezer Evaporator Fan Assembly
(632-2, 642-2, 661-2)

Two screws at the top of the evaporator fan shroud
secure the evaporator fan assembly to the evaporator
brackets at the back of the evaporator.

To remove the evaporator fan assembly, remove the
freezer shelves, ice bucket and duct/shelf assembly
first, then

(See Figures 7-102):

Disconnect evaporator fan wire leads from wire har-
ness.

Extract retaining screws at top of evaporator fan
shroud.

Pull fan assembly up, slightly forward, and out.

Freezer Evaporator Cover (632-2, 642-2, 661-2)

A grounding screw secures the evaporator cover to a
bracket at the front of the evaporator. The evaporator
cover also bends back underneath the evaporator to act
as the drain trough.

To remove the evaporator cover, remove the freezer
shelves, ice bucket and duct/shelf assembly first, then

(See Figures 7-103):

Extract ground screw at front of evaporator cover.

Lean evaporator cover forward to gain access to
drain tube heater, then pull drain tube heater from
drain tube.

Pull evaporator cover forward while pulling drain
tube off of drain spout.

Figure 7-102. Evaporator Fan

Figure 7-101. Defrost Terminator

Figure 7-103. Evaporator Cover

Defrost Terminator

Evaporator Fan Assembly

Screws
(2)

Evaporator
Cover

Drain
Tube
Heater

Содержание 600-2 Series
































































Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды

Sub-Zero 600-2 Series, Руководство по обслуживанию

Результаты поиска

Содержание 600-2 Series

Отзывы:

Похожие инструкции для 600-2 Series

Бренды по названию

Популярные бренды