background image

- 28 -

Cont...

9.1 

Error displays:

  When any of the following errors are displayed call TechAssist on    

 

+44 (0) 800 31 969 80 for a service engineer.

Water/Steam being 

seen at the discharge 

pipe or tundish

User to..

Turn off the system at the isolator or consumer unit. 

Turn on a hot tap until it runs cold to reduce the pressure 

and temperature. 

Turn on the radiators – ensuring all thermostatic valves are 

open. 

Contact Installer.

Pipework installation

Installer: 

Check there are no restrictions in the hot water pipework. 

Loss of pressure in 

expansion vessel

Check for loss of pressure in the hot water expansion vessel. 

Check for loss of pressure in the heating expansion vessel.

Pressure Relief valve 

activated

Check for back feed of high mains pressure from expansion 

valve.

Check pressure reducing valve (on combination valve) 

Heating system malfunction The heating system should not be run with all the radiators 

turned off unless there is a bypass valve in the system 

Check for air in the heating system

Check that the cylinder temperature sensor has not been 

dislodged from the phial in the cylinder. 

With the heating elements and heating pump turned OFF: 

check for error messages on the Electrastream Control unit; 

check target temperature of the Electrastream control unit

Error Code

What does it mean?

ERROR 1

When displayed, it indicates a faulty or disconnected temperature sensor. Heating is 

disabled.

ERROR 2

When displayed, it indicates either the auxiliary 5 amp fuse has blown or the pump, 

motorised valve or room thermostat is fault or that the heating is disabled. 

ERROR 3

When displayed, it indicates that ALL heating elements failed heater test. Heating is 

disabled. 

ERROR 5

One or more of the controller ‘set’, ‘up’, ‘down’ or ‘boost’ buttons are stuck or held down. 

HEAT

When ! is displayed under Heat 1, Heat 2 or Heat 3 it indicates a tri-core element has 

failed. Check the resettable thermal trips in the Electrastream Control unit. 

Содержание BEP 130

































Отзывы: