Still EXD 18 Скачать руководство пользователя страница 87

Страница: 87 / 146

The charger adapts automatically to the bat-

tery discharge situation and therefore allows

any type of partial charging to be carried out

("opportunity charging").
The overcharging calculation takes into ac-

count partial recharging. The mixture is always

sufficient, without needless water consump-

tion, which prevents premature wear of the

batteries (often due to overlong charging peri-

ods) and reduces the need for maintenance.

Protection during charging

Mains micro-break protection
If the mains power is cut off, all the existing

charging parameters are stored in the memory

for 13 minutes. As soon as the mains power

returns, charging resumes from the point (I, U)

at which it was cut off, with the number of Ah

already injected stored in the memory.
If the cut-off period is longer than 13 minutes

(the truck could have been used), a complete

charging cycle is initialised.

Time protection
If the duration of phases I1 + P + U is more

than 16 hours, the charger automatically

stops. This can happen when a battery has a

short-circuited component. Simply reset the

mains to clear the fault.
Temperature safety
As the charger is cooled by ventilation, the air

inlets and outlets must never be blocked.
The fan runs when the mains power is con-

nected. It stops when charging is complete or

when the mains power is disconnected.
The charger supplies reduced power if the

ambient temperature exceeds the usage tem-

perature range in order to protect itself (the

charging period will be extended in this case).
The charger stops if the micro-controller de-

tects a temperature measurement fault.

Using the on-board charger

NOTE

The charger is compatible with wet lead and

gel batteries with a maximum capacity of 400

Ah.

CAUTION

Do not disconnect the battery connector during

charging (green indicator light flashes).
The truck cannot be operated during charging.

The on-board charger is for recharging the

battery.

–

Switch off the truck.

Do not pull the emergency stop handle. This

operation cuts off the circuits and stops the

battery from charging.

–

Connect the charger plug (1) to a mains

wall socket.



Use

Handling the battery

1160 801 15 51 EN - 02/2021 - 11

Содержание EXD 18



















































































































































Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды

Still EXD 18, Оригинальное руководство пользователя

Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды