Still EXD 18 Скачать руководство пользователя страница 107

Страница: 107 / 146

Recommended lubricants

DANGER

Toxic products.
Oils and other consumables are toxic products. It is

advisable to handle and use them with the utmost

care.

Hydraulic oil

Recommended oil for standard use:
ISO-L-HM 46 as per ISO 6743-4 or ISO

VG46-HLP as per DIN 51524-2.
Recommended oil for heavy-duty use:
ISO-L-HM 68 as per ISO 6743-4 or ISO

VG68-HLP as per DIN 51524-2.
Recommended oil for the cold store version:
ISO-L-HM 32 as per ISO 6743-4 or ISO

VG32-HLP as per DIN 51524-2.

NOTE

If in doubt, please ask your local dealer for ad-

vice. You should also consult your local dealer

if a representative of an oil company offers

you an oil product that is not specified in these

operating instructions. Only the oils listed

above are approved by the manufacturer. Us-

ing oil mixtures or hydraulic fluids that are not

recommended can cause damage that may be

expensive to rectify.

Transmission gear oil

Recommended oil:

SAE 85W 90 API GL4

Aerosol can for chains

Standard chain spray.
If in doubt, please ask your local dealer for ad-

vice. You should also consult your local dealer

if a representative of an oil company offers

you an oil product that is not specified in these

operating instructions.

Multi-purpose grease

Lithium soap grease, extreme pressure with

anti-wear additive - Standard DIN 51825 -

KPF 2K - 30, KPF 2K - 20, KPF 2N - 30.

ENVIRONMENT NOTE

Used oil must be stored safely until it is dis-

posed of in compliance with environmental

protection measures. No one should have ac-

cess to the used oil. Do not dispose of used oil

in drains or allow it to penetrate soil.

ENVIRONMENT NOTE

Do not allow the product to disperse into the

environment. Packaging that has contained

this product is treated as waste. Contaminated

packaging must be completely emptied and

may then be recovered following a thorough

clean.

Maintenance

Recommended lubricants

1160 801 15 51 EN - 02/2021 - 11

Содержание EXD 18



















































































































































Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды

Still EXD 18, Оригинальное руководство пользователя

Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды