Still EXD 18 Скачать руководство пользователя страница 24

Страница: 24 / 146

Hydraulic fluid

WARNING

During operation of the forklift truck, hy-

draulic fluids are pressurised and are

hazardous to your health.

–

Do not spill these fluids!

–

Follow the statutory regulations

–

Do not allow the fluids to come into

contact with hot motor parts.

–

Do not allow to come into contact with

the skin.

–

Avoid inhaling the spray

–

Penetration of pressurised fluids into

the skin is particularly dangerous if

these fluids escape at high pressure

due to leaks in the hydraulic system.

In case of such injury, seek medical

advice immediately.

–

To avoid injury, use appropriate per-

sonal protective equipment (e.g. pro-

tective gloves, industrial goggles, skin

protection and skin care products).

ENVIRONMENT NOTE

Hydraulic fluid is a water-polluting substance!
Always store hydraulic fluid in containers com-

plying with the regulations.
Avoid spilling.
Spilt hydraulic fluid should be removed with

oil-binding agents at once and disposed of ac-

cording to the regulations.
Dispose of old hydraulic fluid according to reg-

ulations.

Battery acid

WARNING

Battery acid contains dissolved sulphuric

acid. This is toxic.

–

Avoid contact and consumption.

–

In case of injury, seek medical advice

immediately.

WARNING

Battery acid contains dissolved sulphuric

acid. This is corrosive.

–

When working with battery acid, al-

ways wear protective clothing and

eye protection.

–

Do not allow any acid to get onto the

clothing or skin or into the eyes; if this

does happen, rinse immediately with

plenty of clean water.

–

In case of injury, seek medical advice

immediately.

–

Immediately rinse away spilt battery

acid with plenty of water.

–

Follow the statutory regulations

ENVIRONMENT NOTE

–

Dispose of used battery acid in line with the

applicable regulations.

Safety

Safety regulations for handling consumables

1160 801 15 51 EN - 02/2021 - 11

Содержание EXD 18



















































































































































Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды

Still EXD 18, Оригинальное руководство пользователя

Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды