Still EXD 18 Скачать руководство пользователя страница 44

Страница: 44 / 146

List of checks prior to start-up

WARNING

Damage or other defects on the forklift truck or at-

tachments (special equipment) can result in acci-

dents.
If damage or other faults are noticed on the truck or

attachments (special equipment) during the following

inspections, do not use the truck until it has been

properly repaired. Do not remove or disable the safe-

ty systems and switches. Do not change the pre-set

values.

WARNING

Risk of falling!
When working on high-level parts of the truck, do not

use truck components for access or to stand on.

–

Use suitable access equipment.

Before start-up, ensure that the truck operates

correctly.
To do this, perform the following checks:

–

Fork arms or other load-carrying equipment

should not show any signs of noticeable

damage (for example: bending, cracks, sig-

nificant wear).

–

Check that there are no signs of leaking

consumables under the truck.

–

Do not restrict the field of vision. Ensure the

visible area specified by the manufacturer is

observed.

–

Attachment parts (special equipment) must

be properly secured and function according

to their operating instructions.

–

Damaged or missing stickers must be re-

placed in compliance with the marking posi-

tion table.

–

The guard grille must be intact and securely

mounted.

–

The roller guide rails must be coated in a

visible layer of grease.

–

The wheels must show no signs of defects

or heavy wear. They must be mounted cor-

rectly.

–

Check that there are no foreign objects that

could hinder the operation of the wheels

and rollers.

–

The warning devices (horn etc.) must work.

–

The battery cover must be closed.

–

Check that the covers are correctly posi-

tioned.

–

The chains must be in perfect condition and

must be evenly and correctly tensioned.

–

The operator must be qualified to drive the

truck. The operator must be able to reach

the controls and operate them (especially

the anti-crush device). Do not obstruct ac-

cess to the controls.

Please inform your supervisor if you notice

any defects.

Use

List of checks prior to start-up

1160 801 15 51 EN - 02/2021 - 11

Содержание EXD 18



















































































































































Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды

Still EXD 18, Оригинальное руководство пользователя

Результаты поиска

Содержание EXD 18

Отзывы:

Похожие инструкции для EXD 18

Бренды по названию

Популярные бренды