background image

Edition 

2016

Workshop Manual 

PARK 120 - PARK 220

Chapter

 1 General instructions

Page

3

Table of contents
1.1 Introduction ............................................................................................................4

1.1.1  Limited liability .................................................................................................4

1.1.2  How to read this manual ..................................................................................4

1.1.3  Symbols, General warnings .............................................................................4

1.1.4 Abbreviations ...................................................................................................5

1.1.5  Safety instructions ...........................................................................................5

1.1.6 Lifting ...............................................................................................................6

1.1.7  Spare parts ......................................................................................................6

1.2 Warranty..................................................................................................................6

1.2.1  Warranty period ...............................................................................................6

1.2.2 Exceptions .......................................................................................................6

1.2.3  Interventions carried out after warranty expiry ................................................7

1.2.4  Reporting faults ...............................................................................................7

1.2.5  Ordering spare parts ........................................................................................7

1.3  Identification ...........................................................................................................8

1.4  Unpacking, assembly ............................................................................................9

1.4.1 Assembly .........................................................................................................9

1.4.2 Battery .............................................................................................................9

1.4.3  Final inspections ............................................................................................10

1.5 Maintenance .........................................................................................................11

1.5.1  General safety checks ...................................................................................12

1.5.2  Electrical safety check ...................................................................................12

1.6  Technical data ......................................................................................................14

1.6.1  Machine dimensions ......................................................................................14

1.6.2  General tightening torques ............................................................................14

1.7  User guide ............................................................................................................14

1  General instructions

This manual refers to the PARK 120 - PARK 220. The technical data can be found also in 

the “INSTRUCTION MANUAL”.

This manual does not contemplate repairs to the engine or the transmission. In the event 

of any problems concerning engines and transmission parts, contact the relative Service 

Centre.

This manual and relative specifications refer to the machine in its original state. This 

manual does not cover machines which have undergone modifications designed to alter 

the machine itself.

Содержание PARK 120 2016











































































Отзывы: