manualshive.com logo in svg

Stiga PARK 120 2016, Руководство по ремонту

Поделиться
Скачать
Stiga PARK 120 2016 Скачать руководство пользователя страница 11

Edition 

2016

Workshop Manual 

PARK 120 - PARK 220

Chapter

 1 General instructions

Page

11

1.5 

Maintenance

Maintenance point

First time

Maintenance 

interval

See Chap. par.

“Service hours/

Months”

General safety checks.

5

50/12

 

1.5.1

 

 

1.5.2

Tyre pressure, check, 

adjust.

5

50/12

 

Tyre, air pressure

Engine oil, change.

5

50/12

 

Engine oil

Drive belts, check.

5

50/12

 

Drive belts, check

Steering adjustment.

5

50/12

 

Steering, adjustment

Lubrication of the bearings 

in the articulation.

5

50/12

 

2.3

Lubrication of the shaft on 

the front wheels and quick 

connections.

50/12

 

2.3

Engine  air  filter,  clean/

change.

100/24

 

Engine air filter

Spark plug, change/

replace.

100/24

 

Spark plug

Transmission, check.

100/24

 

Transmission

Exhaust system, check.

100/24

 

Exhaust system

Electrical system, check.

100/24

 

Electrical system

PTO, check.

100/24

 

Power take-off

Check controls.

100/24

 

Check controls

Valve play.

100/24

For the engine, refer to the 
dedicated manual

Test driving.

100/24

 

Test drive

Содержание PARK 120 2016











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды