Stiga PARK 120 2016 Скачать руководство пользователя страница 8

Страница: 8 / 74

Edition

2016

Workshop Manual

PARK 120 - PARK 220

Chapter

1 General instructions

Page

1.3

Identification

Machine

kW -

/min

Each machine is supplied with a label (1) affixed

behind the seat, indicating the technical data, the

model and the serial number.

The model and serial number must be indicated

on the intervention sheet, when requesting

application of the warranty and are indispensable

in the ordering of spare parts.

Transmission

This machine is equipped with 1 hydrostatic

transmission.

This component is supplied by an external

manufacturer and is built to precise technical

specifications which distinguish it from similar

products made by the same manufacturer. The

serial number indicated on the label (1) makes it

possible to correctly identify the product and its

characteristics and must always be cited when

ordering spare parts or requesting any information

from the Manufacturer.

Engine

The engine is built to precise technical

specifications which distinguish it from similar

products made by the same manufacturer. The

serial number indicated on the label (1) makes it

possible to correctly identify the product and its

characteristics and must always be cited when

ordering spare parts or requesting any information

from the Manufacturer.

Содержание PARK 120 2016











































































Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды

Stiga PARK 120 2016, Руководство по ремонту

Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды