Stiga PARK 120 2016 Скачать руководство пользователя страница 54

Страница: 54 / 74

Edition

2016

Workshop Manual

PARK 120 - PARK 220

Chapter

7 Electrical system

Page

The starter motor does not rotate

Do you hear “click” from the start

relay at the start attempt?

YES

Does the starter motor register any

current flow?

YES

Is the engine grounded towards the battery?

NOT

YES

Change start relay

Correct the

problem

Check the

starter motor

Is there voltage to the ignition

switch?

NOT

Check the battery

YES

Is there voltage at the parking

brake switch?

NOT

Change the ignition switch

YES

Is there voltage at the start relay?

NOT

Change the parking brake switch

YES

Is there ground at the start relay?

YES

Change the start relay

NOT

Change the seat switch (Black)

The starter motor rotates, but the engine will not start

Check the fuel valve function.

Is the valve broken?

YES

Change the fuel valve

NOT

Remove the short circuit cable from

the engine. Does the engine start?

YES

Check the ignition switch. M-G will

only have contact in stop position

YES

Check if the short circuit cable is damaged or

accidentally connected to ground.

NOT

Check the engine using the engine

manual

Replace the ignition switch

Содержание PARK 120 2016











































































Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды

Stiga PARK 120 2016, Руководство по ремонту

Результаты поиска

Содержание PARK 120 2016

Отзывы:

Похожие инструкции для PARK 120 2016

Бренды по названию

Популярные бренды