STIEBEL ELTRON SOM 7 PLUS Скачать руководство пользователя страница 4

Страница: 4 / 52

display

push button

fuse 4A

cable conduits with strain
relief

cover

1.1 Mounting

The unit must only be installed

• in a dry interior location

• in a non-hazardous location

• away from electromagnetic fields

The controller must additionally be supplied from a double-
pole switch with contact gap of at least 0.12".
Route sensor cables and power supply cables separately.

Unscrew the cross-head screw from the cover and remove
it along with the cover from the housing

Mark the upper fastening point on the wall and drill

Fasten the enclosed wall plug and screw leaving the head
protruding

Hang the housing from the upper fastening point and
mark the lower fastening point through the hole in the
terminal box (centers 5.1")

Drill and insert the lower wall plug

Fasten the housing to the wall with lower fastening screw
and tighten

Complete wiring connections in accordance with terminal
allocations, see chap. 1.2 “Electrical connection”

Place the cover back onto the housing

Fasten the cover by means of the cross-head screw

1. Installation

. „

upper fastening

lower fastening

VBus

1.2 Electrical connection

power supply terminals

fuse

load terminals

sensor terminal

ground terminal

Note:

The minimum pump speed must be set to 100 % when
auxiliary relays or valves are connected.

WARNING!

Electric shock!
Opening the housing will expose live
parts!

Switch off power supply and disconnect
the device from power supply before
opening the housing!

ATTENTION!

ESD damage!
Electrostatic discharge can lead to
damage to electronic components!

Take care to discharge properly
before touching the inside of the
device. To do so, touch a grounded
surface such as a radiator or tap!

Содержание SOM 7 PLUS





















































Результаты поиска

Содержание SOM 7 PLUS

Отзывы:

Похожие инструкции для SOM 7 PLUS

Бренды по названию

Популярные бренды

STIEBEL ELTRON SOM 7 PLUS, Эксплуатация и установка

Результаты поиска

Содержание SOM 7 PLUS

Отзывы:

Похожие инструкции для SOM 7 PLUS

Бренды по названию

Популярные бренды