manualshive.com logo in svg

Stewart Filmscreen Luxus, Руководство пользователя

Поделиться
Скачать
Stewart Filmscreen Luxus Скачать руководство пользователя страница 10

 

  Stewart Filmscreen – Luxus 

10 

 

 

CEILING MOUNT   

 

 

 

 

 

 

 

 

 

 

 

Professional mounting techniques should be used. Stewart Filmscreen cannot be liable for substandard 
or faulty installations. Failure to comply with the instructions and guidance contained in this manual 
may result in voiding the warranty. 

 

1.

 

Use a magnetic stud finder, or similar appropriate 
means, to identify the location of solid ceiling joists. If 
the joists or rafters are parallel to the screen case, 
blocking is required between structural elements. 

2.

 

Use a level or other straight edge to properly align both 
ceiling mounts as straight as possible. 

3.

 

Screws must be mounted into solid wood. If no joists 
are available then the ceiling must be blocked.   

4.

 

Screw the ceiling brackets into the joists (see Figure 8). 
Ensure the screws are mounted to solid wood and that 
both ceiling brackets are properly aligned to each other.  

5.

 

Lift the case up to the ceiling and into the mounting 
brackets. Gently slide case backwards about 1/2" to 
engage and lock into brackets (see Figure 9).   

6.

 

Since both mounts do not need to be equidistant to the 
sides of the case, you can float the case left and right to 
find the perfect position even after the screen is 
mounted.  

 
 
 
 
 
 
 

⚠

 

CAUTION

 

During installation, do not place the unit on an unstable cart, stand, table or ladder. The 
unit may fall, causing injury to you or others as well as cause possible damage to the unit.  

Do not mount to drywall only. There must be wood joists behind the drywall to secure 
the screen. 

 

Figure 8.  Ceiling bracket 

screwed onto ceiling joists   

Figure 9.  Luxus case extrusion with 

ceiling mount extrusion 

Содержание Luxus
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды