background image

 

 

 

Stewart Filmscreen –

 

Balón 

 

 

 

INSTALLATION PREPARATION  

 

 

 

Before proceeding with the installation of the screen, take time to thoroughly read and understand 
these installation instructions. Failure  to comply  with  the instructions  contained  in  this  manual 
may result in voiding your warranty. 

1.

 

Make sure there is a clean surface on which to unroll the screen and assemble the frame.

 

2.

 

Check the size and weight of the screen to be installed so that you can plan for the number of 
people  required  for  installation.  Specifications  regarding  the  individual  screen  dimensions, 
weight, etc. are provided by the factory when the screen is ordered. 

 

3.

 

You will need at least two people to mount the screen, depending on the size and weight of the unit. More 

are needed for larger, heavier screens.

 

 

What’s Inside the Box? 

Inside the box you will find everything needed to get started on enjoying your Balón screen. 

  Screen material placed in a tube with packing material for protection 

  Disassembled frame and all necessary hardware to re-assemble frame 

  Hanging bar and mounting hardware 

  LED lighting kit, if ordered 

  White cloth gloves (for UST Material only) 

  Quick Start Guide 

 

 

You Will Need:

 

 

A level 

 

A drill 

 

A drop cloth 

 

Tools for tightening fasteners 

 

Lint-free, clean cloth gloves for handling the screen 

 

Ladders for the personnel supporting the screen during the mounting process 

 

Fasteners appropriate for the surface on which the screen is being mounted 

 

Note:

 

Bolts and other fasteners for the screen are standard gauge and are sized for use in the 

USA. For this reason, the sizes are expressed in inches rather than metric measurements. 

 
 
 
 
 
 

 

Содержание Balon Series
























Отзывы: