STEMMER IMAGING GARDASOFT PP8 Series Скачать руководство пользователя страница 32

Страница: 32 / 36

WWW.STEMMER-IMAGING.COM

PP8xx LED Controller - User Manual

Where:

output channel (0 to 7)

pulse width in microseconds

delay from trigger to pulse in microseconds

output current in amps

retrigger delay in microseconds (optional).

For example: Set channel 2 to pulsed output at 4A, with a pulse
width of 1ms after a delay of 500us:

RT2,1000,500,4

10.5 Command summary

Command

Example

Effect

Save changes.

ST2

Show configuration for channel 2.

Read the firmware version.

RS2,0.7

Set channel 2 to 0.7A continuous.

RW1,1.1

Set channel 1 to 1.1A, switched by
input 1.

RT2,3,4,1.9

Set channel 2 to 3ms pulses, delayed by
4ms, with an output pulse current of
1.9A.

FP1

Trigger all channels from trigger 0 input.

TT1,1ms

Set test mode with pulses every 1ms.

Clear all output settings.

TR2

Trigger channel 2.

EY65,66

Set webpage password to 'AB'.

Read any error messages.

GT1

Enable Ethernet messages.

—

WWW.STEMMER-IMAGING.COM

Содержание GARDASOFT PP8 Series





































Результаты поиска

Содержание GARDASOFT PP8 Series

Отзывы:

Похожие инструкции для GARDASOFT PP8 Series

Бренды по названию

Популярные бренды

STEMMER IMAGING GARDASOFT PP8 Series, Руководство пользователя

Результаты поиска

Содержание GARDASOFT PP8 Series

Отзывы:

Похожие инструкции для GARDASOFT PP8 Series

Бренды по названию

Популярные бренды