STEMMER IMAGING GARDASOFT PP8 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

background image

WWW.STEMMER-IMAGING.COM

PP8xx LED Controller - User Manual

Three modes of operation can be provided independently to each
channel:

Continuous:

In continuous mode, the output is constant.

Pulsed:

Also referred to as 'strobed', this output mode produces one

pulse on the receipt of a trigger input. The pulse width can range from 1μs
to 300ms in 0.1μs steps. The delay can range from 4μs to 300ms in 0.1μs
steps.

Switched:

In switched mode, a trigger input can be used to switch the

output current on and off. The output is only enabled when the input has a
voltage on it.

Triggers occur on the leading edge of the input, that is, on the transition
from logic 0 to logic 1. Output 1 is triggered from Input 1, output 2 from
Input 2, and so on.

Configurations can be saved in non-volatile memory so that the PP8xx will
resume operation after a power cycle.

—

8

—

WWW.STEMMER-IMAGING.COM

«
...
4
5
6
7
8
...
»

Содержание GARDASOFT PP8 Series





































Отзывы:

Нет отзывов

Похожие инструкции для GARDASOFT PP8 Series

Бренд: Ebyte Страницы: 34

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: Warren Controls Страницы: 16

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: KaRo Страницы: 12

Бренд: Matelec Страницы: 16

Бренд: Voltech Страницы: 8

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

963325-0403 - RumblePad 2 Vibration Feedback Gamepad Game Pad

Бренд: Logitech Страницы: 2

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: PS Automation Страницы: 4

Бренд: Nice Страницы: 32

Бренд: Rabbit Страницы: 12

Бренд: phytron Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды