STEMMER IMAGING GARDASOFT PP8 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

background image

WWW.STEMMER-IMAGING.COM

PP8xx LED Controller - User Manual

7

Connecting the PP8xx

Refer to

Section 11, PP8xx reference information

for the ratings of the

connections. To prevent overload of output wiring, all power and output
cabling must be rated for a continuous load current of 6.3A minimum.
However, this does not apply to the Ethernet, RS232 and trigger input
connections.

The PP8xx's connections are shown below:

7.1

Power

Any power supply derived from mains electricity must have a Safety Extra
Low Voltage (SELV) output. Route low voltage wiring to the PP8xx
controller separately from mains electricity wiring.

Please refer to

Section

2, Safety

.

If this is not possible, make sure the low voltage wiring has an insulation
rating that is appropriate or supplementary insulation is used. The
connections are shown below:

Note:

The case of the PP8xx is not connected to GND.

—

20

—

WWW.STEMMER-IMAGING.COM

«
...
16
17
18
19
20
...
»

Содержание GARDASOFT PP8 Series





































Отзывы:

Нет отзывов

Похожие инструкции для GARDASOFT PP8 Series

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Calsense Страницы: 74

Бренд: Eaton Страницы: 288

Бренд: VAT Страницы: 26

Бренд: Vanderbilt Страницы: 2

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: Paradox Страницы: 3

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: Pfeiffer Vacuum Страницы: 100

Бренд: Vent-Axia Страницы: 4

Бренд: Viva Страницы: 9

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды