STEMMER IMAGING GARDASOFT PP8 Series Скачать руководство пользователя страница 34

Страница: 34 / 36

WWW.STEMMER-IMAGING.COM

PP8xx LED Controller - User Manual

11.2 Error codes

Error codes may be sent by Ethernet or RS232. These are shown as

Err

, where

gives the number of the error. The error codes are:

Error number

Reason

Err01

One of the parameters of a command has an illegal
value.

Err02

Command not recognised.

Err03

Failed to save parameters to non-volatile memory.

Err04

The command has the wrong number of
parameters.

Err05

This is a warning, not an error. A timing parameter is
out of range and the value of that parameter has
been adjusted.

Err18

On power-up, the stored configuration was invalid

Err40

When the unit has powered up the non-volatile
memory was corrupt and has been cleared. Set up
the unit again.

All other errors

A hardware error has occurred. Try power cycling
the unit and see if the fault clears. If not, note the
error number and contact your distributor.

—

WWW.STEMMER-IMAGING.COM

Содержание GARDASOFT PP8 Series





































Результаты поиска

Содержание GARDASOFT PP8 Series

Отзывы:

Похожие инструкции для GARDASOFT PP8 Series

Бренды по названию

Популярные бренды

STEMMER IMAGING GARDASOFT PP8 Series, Руководство пользователя

Результаты поиска

Содержание GARDASOFT PP8 Series

Отзывы:

Похожие инструкции для GARDASOFT PP8 Series

Бренды по названию

Популярные бренды