SteelMax SBM-500 Скачать руководство пользователя страница 7

Страница: 7 / 44

SBM-500

SBM-

500 Operator’s Manual

2. SAFETY PRECAUTIONS

Before use, read this Operator’s Manual and complete a training in occupational

safety and health.

2. Use only in applications

specified in this Operator’s Manual.

3. Make sure that the machine has all parts and they are genuine and not damaged.

4. Make sure that the specifications of the power source are the same as those

specified on the rating plate.

5. Connect the machine to a 3×480 V + PE power source. Protect the power source

with a 25 A three-phase slow-blow fuse. If you use a residual-current circuit

breaker, it must be of type B and of value of at least 300 mA.

6. Do not pull the cord. This can cause damage and electric shock.

7. Keep the machine in vertical position during transport and work.

8. Put the machine on a surface that ensures balance and efficiently transfers the

loads of the machine and workpiece. An incorrectly prepared surface may lead to

damage, incorrect machine work, and injuries to persons nearby.

9. Keep untrained bystanders away from the machine.

10. Before each use, ensure the correct condition of the machine, power source,

power cord, plug, control panel, and tools.

11. Before each use, make sure that no part is cracked or loose. Make sure to

maintain correct conditions that can have an effect on the operation of the

machine.

12. After the power is off, wait 3 minutes before you open the control cabinet.

13. After the power is off, wait 60 seconds before you turn the power on again.

14. Keep the machine dry. Do not expose the machine to rain, snow, or frost.

15. Keep the worksite well-lit, clean, and free of obstacles.

16. Make sure that the cutting inserts and the milling head are correctly attached.

Remove wrenches from the worksite before you connect the machine to the

power source.

17. Do not use tools that are dull or damaged.

18. If the cutting edge of an insert is worn, rotate all inserts by 90°. If all edges are

worn, install

new inserts specified in this Operator’s Manual.

19. Do not make bevels or use workpieces whose parameters differ from those

specified in the technical data.

Содержание SBM-500













































Результаты поиска

Содержание SBM-500

Отзывы:

Бренды по названию

Популярные бренды

SteelMax SBM-500, Руководство оператора

Результаты поиска

Содержание SBM-500

Отзывы:

Бренды по названию

Популярные бренды