Steelex ST1007 Скачать руководство пользователя страница 13

Страница: 13 / 81

-10-

ST1007/12/14 15" & 20" Planers (Mfd. Since 3/16)

Amputation, serious cuts, entanglement, or death can occur from contact with rotating cutterhead

or other moving parts! Flying chips can cause blindness or eye injuries. Workpieces or knives thrown

by cutterhead can strike nearby operator or bystanders with deadly force. To reduce the risk of these

hazards, operator and bystanders MUST completely heed hazards and warnings below.

PLANING CORRECT MATERIAL. Only plane natural

wood stock with this planer. DO NOT plane MDF,

OSB, plywood, laminates or other synthetic materials

that can break up inside the planer and be ejected

towards the operator.

LOOKING INSIDE PLANER. Wood chips fly around

inside the planer at a high rate of speed during

operation. To avoid injury from flying material, DO

NOT look inside planer during operation.

CUTTING LIMITATIONS. To reduce the risk of kick-

back hazards or damage to the machine, do not

exceed the maximum depth of cut or minimum

board length and thickness found in the Data Sheet.

Only feed one board at a time.

INFEED ROLLER CLEARANCE. The infeed roller is

designed to pull material into the spinning cut-

terhead. To reduce the risk of entanglement, keep

hands, clothing, jewelry, and long hair away from the

infeed roller during operation.

FEED WORKPIECE PROPERLY. To reduce the risk of

kickback, never start planer with workpiece touch-

ing cutterhead. Allow cutterhead to reach full speed

before feeding, and do not change feed speed dur-

ing cutting operation.

WORKPIECE SUPPORT. To reduce the risk of kick-

back, always make sure workpiece can move com-

pletely across table without rocking or tipping. Use

auxiliary support stands for long stock.

SECURE KNIVES/INSERTS. Loose knives or improp-

erly set inserts can become dangerous projectiles or

cause machine damage. Always verify knives/inserts

are secure and properly adjusted before operation.

KICKBACK. Know how to reduce the risk of kickback

and kickback-related injuries. “Kickback” occurs dur-

ing the operation when the workpiece is ejected

from the machine at a high rate of speed. Kickback

is commonly caused by poor workpiece selection,

unsafe feeding techniques, or improper machine

setup/maintenance. Kickback injuries typically occur

as follows: (1) operator/bystanders are struck by the

workpiece, resulting in impact injuries (i.e., blindness,

broken bones, bruises, death); (2) operator’s hands

are pulled into blade, resulting in amputation or

severe lacerations.

AVOID CONTACT WITH MOVING PARTS. Never

remove guards/covers or reach inside the planer

during operation or while connected to power. You

could be seriously injured if you accidentally touch

the spinning cutterhead or get entangled in mov-

ing parts. If a workpiece becomes stuck or sawdust

removal is necessary, turn planer OFF and disconnect

power before clearing.

DULL/DAMAGED KNIVES/INSERTS. Only use sharp,

undamaged knives/inserts. Dull or damaged knives/

inserts increase the risk of kickback.

INSPECTING STOCK. To reduce the risk of kickback

injuries or machine damage, thoroughly inspect and

prepare the workpiece before cutting. Verify work-

piece is free of nails, staples, loose knots or foreign

material. Workpieces with minor warping should be

jointed first or planed with the cupped side facing

the table.

BODY PLACEMENT. Stand to one side of planer

during the entire operation to avoid getting hit if

kickback occurs.

GRAIN DIRECTION. Planing across the grain is hard

on the planer and may cause kickback. Plane in the

same direction or at a slight angle with the wood

grain.

Additional Safety for Planers

Содержание ST1007


















































































Результаты поиска

Содержание ST1007

Отзывы:

Похожие инструкции для ST1007

Бренды по названию

Популярные бренды

Steelex ST1007, Руководство пользователя

Результаты поиска

Содержание ST1007

Отзывы:

Похожие инструкции для ST1007

Бренды по названию

Популярные бренды