manualshive.com logo in svg

Steelcase Secant Options Worksurface Supports, Руководство пользователя

Поделиться
Скачать
Steelcase Secant Options Worksurface Supports Скачать руководство пользователя страница 35

1

2

3

5

6

4

Page 35 of 38

939504792 Rev D

STRAIGHT LEG 

MOUNTING PLATE

PRESS

See pages 31 and 34.

PILOT

HOLE

P

P

NOTE:
Height-adjustment buttons
and notches face inward
as shown, away from the user.

Tethered Spanner Assembly 

1.

On a non-abrasive surface (such as a
shipping blanket or carpeting) free of screws, 
tools and other debris that may damage it, 
flip the worksurface over so its pilot holes 
are visible.

2.

On each straight leg, identify the two (2) 
holes that will align with the pilot holes in 
the worksurface.

3.

Align both front straight legs with the pilot 
holes, such that the notch in the plate faces 
the interior of the worksurface.  ATTACH 
EACH LEG WITH TEN (10) "A" SCREWS.

4.

Before flipping the worksurface back over, 
adjust the height of the attached legs to 
match that of the tethered system to which 
the spanner will attach.

5.

Attach spanner to front shared legs of tethered 
system.

6.

Attach two (2) stealth plates as shown on 
pages 31 and 34.

Содержание Secant Options Worksurface Supports







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды