manualshive.com logo in svg

Steelcase Avenir Panel Worksurface with Pedestal to the Floor, Руководство пользователя

Поделиться
Скачать
Steelcase Avenir Panel Worksurface with Pedestal to the Floor Скачать руководство пользователя страница 5

Page 5 of 18

939501051 Rev G

Remove front and rear aprons (Items 21 and 25) from one of the pedestal drawers.  Next insert tab on front apron 
(Item 25) into slot on rear apron (Item 21).  Now align front and rear apron mounting holes with pre-drilled holes in 
bottom of worksurface.  Next secure aprons to worksurface with (4) screws (Item 7).  Refer to Fig. G.

NOTE:  Install screw when attaching 
apron to a cantilevered support or 
end panel.  Remove knock-out in apron.

21

25

7

Fig G

Remove front and rear mounting brackets (Item 8 and 10) from pedestal (Item 14).  Save Screws.  Next align front
and rear mounting bracket mounting holes with pre-drilled holes in bottom of worksurface (Item 6).  Now secure 
mounting brackets to worksurface with (3) screws (Item 7) each.  Refer to Fig. H. 

7

10

8

6

Fig H

3.

  Installation of front and rear

aprons with 29" deep pedestals.
A RH. installation is shown, LH.
is typical.

4.

  Installation of front and rear

mounting brackets for 19" deep
pedestals.  A RH. installation is
shown, LH. is typical.4.

Содержание Avenir Panel Worksurface with Pedestal to the Floor



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды