manualshive.com logo in svg

Steelcase Avenir Panel Worksurface with Pedestal to the Floor, Руководство пользователя

Поделиться
Скачать
Steelcase Avenir Panel Worksurface with Pedestal to the Floor Скачать руководство пользователя страница 16

Page 16 of 18

939501051 Rev G

LOCATING 

HOLES

Fig C

View in direction of arrow A

RETAINER PLATE

RETAINER PLATE

SHARED CANTILEVER
SUPPORT BRACKET 

1”

Assemble parent worksurfaces and cantilevered
supports to moveable wall system, in the
same manner shown on pages 4 and 8.
Position curved corner worksurface onto
shared support brackets as shown.  Insert
(2) no. 12 x 7/8" screws into locating holes
thru the shared support brackets as shown
in the view in direction of arrow A. Position
the retainer plates and insert (1) no. 12 x 7/8"
screw into the locating hole. Using the slots
in the retainer plates and shared support
brackets as a template, drill a 7/32" dia. x 3/4"
deep hole (3) places for the shared support
bracket and (5) places for the retainer plate
into the bottom of the worksurfaces. Insert
screws, align worksurface and tighten all
screws. 

Содержание Avenir Panel Worksurface with Pedestal to the Floor



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды