Steelcase Avenir Panel Worksurface with Pedestal to the Floor Скачать руководство пользователя страница 1

Страница: 1 / 18

Page 1 of 18

939501051 Rev G

Avenir

Panel Worksurface

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at

888.STEELCASE

(888.783.3522)

for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com

2004 Steelcase Inc.

Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.

Panel Worksurface
with Pedestal to the Floor

Panel Worksurface
with Suspended Pedestal
and Aprons

Panel Worksurface
with Suspended Pedestal
Without Aprons

7/32" Drill Bit

1/2" & 3/8" Sockets

NOTE:

For floor-supported pedestals manufactured

after Feb 2004, see assembly direction 939503252.

NOTE:

For suspended pedestals manufactured after

Feb 2004, see assembly direction 939503249.

Содержание Avenir Panel Worksurface with Pedestal to the Floor



















Результаты поиска

Содержание Avenir Panel Worksurface with Pedestal to the Floor

Отзывы:

Похожие инструкции для Avenir Panel Worksurface with Pedestal to the Floor

Бренды по названию

Популярные бренды

Steelcase Avenir Panel Worksurface with Pedestal to the Floor, Руководство пользователя

Результаты поиска

Содержание Avenir Panel Worksurface with Pedestal to the Floor

Отзывы:

Похожие инструкции для Avenir Panel Worksurface with Pedestal to the Floor

Бренды по названию

Популярные бренды