Steelcase 7.2 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

background image

Page 7 of 20

18719901 Rev G

®

For 3-Leg Tables:

With the top still upside down on the floor, turn the base
over (flipping is a 2 person job), and align the attachment
plates to the pre-drilled holes in the top. For 3-leg tables,
align the center lifting column first.

Center each pre-drilled hole in the top to the slot in the
attachment plate. Loosely install one fastener in each of
the pre-drilled pilot holes.

Once the center lifting column is secured, align the left
and right lifting columns in a similar fashion by moving
the plate so that all pre-drilled holes are visible.

Don't install all fasteners until the unit has been operated
through one cycle (Step 14).

NOTE: Do not force the left or right lifting
columns to perfectly fit the attachment
mounting holes. This can cause binding
during articulation.

SQUARE

DRIVE

SCREW

7

Mounting Legs to Worksurfaces (cont.)

«
...
5
6
7
8
9
...
»

Содержание 7.2 Series





















Отзывы:

Нет отзывов

Похожие инструкции для 7.2 Series

Бренд: ECCB OUTDOOR Страницы: 3

Бренд: IBM Страницы: 4

Бренд: Unfinished Furniture of Wilmington Страницы: 5

Бренд: Unfinished Furniture of Wilmington Страницы: 7

FLIP TOP RECTANGLE TABLE

Бренд: WB Manufacturing Страницы: 2

Бренд: Safavieh Furniture Страницы: 2

Бренд: Quoizel Страницы: 2

Wood Original Chair CCC100

Бренд: Canada Comfy Chair Страницы: 6

Tete-a-tete Double Chair Rounded Wood

Бренд: Canada Comfy Chair Страницы: 3

Бренд: TDC USA Страницы: 13

Sonoma Clothes Rack A Frame

Бренд: fantastic furniture Страницы: 8

Бренд: Tactix Страницы: 2

Бренд: KidKraft Страницы: 9

Бренд: Coaster Страницы: 4

Бренд: Tech Craft Страницы: 6

Бренд: Montana Страницы: 10

Бренд: Furinno Страницы: 2

Бренд: URBAN OUTFITTERS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды