Stealth Cam STC-G45NGMAX, Инструкция по эксплуатации

Страница: 11 / 54

www.stealthcam.com Page
877-­‐269-­‐8490
11
CAMERA PROGRAMMING -­‐ CUSTOM (CONT)
o
PIR PHOTO (default) :
In this mode the camera will take a designated amount of pictures with a
designated timeout when the camera senses activity in front of the unit. This mode is available for both
day and night activities.
"
PHOTO RES –
8
.0 MP (default) :
This setting is used to determine the Megapixel resolution of each image taken by
the camera. With this option blinking, use the UP or DOWN arrow key to move between the options of: 26MP,
16MP 8MP, or 4MP. The higher the resolution of an image the more space the file will take on the SD memory card.
"
PIR DELAY – 00min 05sec (default): This setting is used to determine the length of the time that the camera will
wait before it reinitializes its PIR sensor for the next activation. With the TL mode this setting is only active if
TL Delay is set to 1 min or greater. This setting can be changed between the numbers
of 00min 0
2
sec to 59min
59sec. With this option blinking, use of the UP and DOWN arrows will allow the minutes setting to be changed
from 00 to 59. Once
th
is setting is on the appropriate minutes, press the RIGHT arrow key to
move to the seconds setting and it will start to blink. Use of the UP and Down arrows will allow the seconds setting
to be changed from 0
0
to 59
min
(0
2
to 59
seconds
if minutes = 00).
"
PIR RANGE – STANDARD (default): This setting allows you to control the sensitivity distance the PIR will be
activated. These distances can vary depending on environmental conditions. This setting will change between
EXTENDED
which will trigger about 1/3 further than the STANDARD setting, the STANDARD setting, or NEAR FIELD
that will only trigger on movement closest to the camera.
"
REDUCE BLUR – ADVANCED (default): This setting is used to determine if the camera should use the MATRIX
Blur reduction technology to dramatically reduce the blur effect resulting in clearer night time infrared shots.
(STANDARD) Minimizes blurring effect in images wh
i
le retaining long
-
range night image capability.
(ADVANCED)
Enhanced blur reduction providing a balance between brightness and image sharpness.
(PROGRESSIVE) Maximum blur reduction achieved through faster shutter speed. This setting may cause a slight
reduction in night time range and increased grain in the image.
With this
option blinking, pressing the UP or DOWN
arrow buttons will cause the camera to cycle between the three options of STANDARD, ADVANCED, and
PROGRESSIVE.
" PHOTO BURST – 1 PHOTO (default): This setting is used to determine the number of photos the camera will take
during its activation. This setting can be changed between 1 PHOTO up to 9 PHOTOS. With this option blinking,
use the UP or DOWN arrow key to move between the value range in increments of 1.
"
BURST INTERVAL - 1 Second (default): This setting is used to determine the delay between multiple burst of photos.
This setting can be changed between 1 SECOND and 5 SECONDS. With this option blinking, use the UP or DOWN
arrow key to move between the settings.
"
IR B RIGHTNESS CONTROL – FULL (default): This setting is used to adjust the brightness of the IR LEDS. With this
option blinking, use the UP or DOWN arrow key to move between FULL and HALF brightness. On FULL brightness
the LEDs have a further flash range making it ideal for large open areas. HALF brightness is ideal for close up shots
preventing the subject from being overexposed.
"
S MART IR - ON (default) : This setting is used to to toggle Smart IR ON and OFF. With this option blinking, use the UP
or DOWN arrow to move between ON and OFF. While enabled the camera will take color images during the dusk
and dawn lighting conditions. While Smart IR is ON, Photo Burst is limited to (1) image per triggering.