Star Headlight & Lantern STARSIGNAL LCS771 Скачать руководство пользователя страница 16

-14- 

ONE YEAR LIMITED WARRANTY 

The  manufacturer  warrants  each  new  product  against  factory  defects  in  material 
and  workmanship  for  one  year  after  the  date  of  purchase.    The  owner  will  be 
responsible  for  returning  to  the  Service  Center  any  defective  item(s)  with  the 
transportation  costs  prepaid.    The  manufacturer  will,  without  charge,  repair  or 
replace 

at  its  option

,  products,  or  part(s),  which  its  inspection  determines  to  be 

defective.    Repaired  or  replacement  item(s)  will  be  returned  to  the  purchaser  with 
transportation  costs  prepaid  from  the  service  point.    A  copy  of  the  purchaser's 
receipt  must  be  returned  with  the  defective  item(s)  in  order  to  qualify  for  the 
warranty  coverage.    Exclusions  from  this  warranty  include,  but  are  not  limited  to, 
bulbs,  strobe  tubes,  domes,  and/or  the  finish.    This  warranty  shall  not  apply  to  any 
light,  which  has  been  altered,  such  that  in  the  manufacturer's  judgment,  the 
performance  or  reliability  has  been  affected,  or  if  any  damage  has  resulted  from 
abnormal use or service. 

 

There  are  no  warranties  expressed  or  implied  (including  any  warranty  of 
merchantability or fitness), which extend this warranty period.  

The loss of use of the 

product,  loss  of  time,  inconvenience,  commercial  loss  or  consequential  damages, 
including costs of any labor, are not covered

.  The manufacturer reserves the right to 

change  the  design  of  the  product  without  assuming  any  obligation  to  modify  any 
product previously manufactured. 

 

This  warranty  gives  you  specific  legal  rights.    You  might  also  have  additional  rights 
that may vary from state to state.  Some states do not allow limitations on how long 
an  implied  warranty  lasts.    Some  states  do  not  allow  the  exclusion  or  limitation  of 
incidental  or  consequential  damages.    Therefore,  the  above  limitation(s)  or 
exclusion(s) may not apply to you.

 

If you have any questions concerning this or any other product, please contact 

our 

Customer Service Department

 at (585) 226-9787. 

 

If a product must be returned for any reason, please contact our  

Customer Service Department to obtain a Returned Materials Authorization  

number (RMA #) before you ship the product back. 

Please write the RMA # clearly on the package near the mailing label. 

NOTICE 

Due  to  continuous  product  improvements,  we  must  reserve  the  right  to  change  any  specifications 
and information, contained in this manual at any time without notice.  Signal Vehicle Products and/or 
the manufacturer make no warranty of any kind with regard to this manual, including, but not limited 
to,  the  implied  warranties  of  merchantability  and  fitness  for  a  particular  purpose.    Signal  Vehicle 
Products  and/or  the  manufacturer  shall  not  be  liable  for  errors  contained  herein  or  for  incidental  or 
consequential damages in connection with the furnishing, performance, or use of this manual. 

Содержание STARSIGNAL LCS771

















Отзывы: