12
ENGLISH
Do not use edge grinding/cutting wheels for sur-
face grinding applications because these wheels
are not designed for side pressures encountered
with surface grinding. Wheel breakage and injury
may result.
Surface finishing with sanding flap discs
u
Allow the tool to reach full speed before
touching the tool to the work surface.
u
Apply minimum pressure to work surface,
allowing the tool to operate at high speed.
Sanding rate is greatest when the tool operates
at high speed.
u
Maintain a 5˚ to 10˚ angle between the tool and
work surface.
u
Continuously move the tool in a forward and
back motion to avoid creating gouges in the
work surface.
u
Remove the tool from work surface before
turning tool off. Allow the tool to stop rotating
before laying it down.
Using sanding backing pads
Choose the proper grit sanding discs for your
application. Sanding discs are available in various
grits. Coarse grits yield faster material removal
rates and a rougher finish.
Finer grits yield slower material removal and a
smoother finish.
Begin with coarse grit discs for fast, rough material
removal. Move to a medium grit paper and finish
with a fine grit disc for optimal finish.
u
Coarse 16 - 30 grit
u
Medium 36 - 80 grit
u
Fine Finishing 100 - 120 grit
u
Very Fine Finishing 150 - 180 grit
u
Allow the tool to reach full speed before
touching tool to the work surface.
u
Apply minimum pressure to work surface,
allowing the tool to operate at high speed.
Sanding rate is greatest when the tool operates
at high speed.
u
Maintain a 5˚ to 15˚ angle between the tool and
work surface. The sanding disc should contact
approximately 25mm of work surface.
u
Move the tool constantly in a straight line to
prevent burning and swirling of work surface.
Allowing the tool to rest on the work surface
without moving, or moving the tool in a circular
motion causes burning and swirling marks on
the work surface.
u
Remove the tool from work surface before
turning tool off. Allow the tool to stop rotating
before laying it down.
Using wire cup brushes and wire wheels
Wire wheels and brushes can be used for re-
moving rust, scale and paint, and for smoothing
irregular surfaces.
Note: The same precautions should be taken when
wire brushng paint as when sanding paint.
u
Allow the tool to reach full speed before
touching the tool to the work surface.
u
Apply minimum pressure to work surface,
allowing the tool to operate at high speed.
Material removal rate is greatest when the tool
operates at high speed.
u
Maintain a 5˚ to 10˚ angle between the tool and
work surface for wire cup brushes.
u
Maintain contact between the edge of the wheel
and the work surface with wire wheels.
u
Continuously move the tool in a forward and
back motion to avoid creating gouges in the
work surface. Allowing the tool to rest on the
work surface without moving, or moving the tool
in a circular motion causes burning and swirling
marks on the work surface.
u
Remove the tool from the work surface before
turning the tool off. Allow the tool to stop
rotating before setting it down.
Use extra care when working over an edge, as
a sudden sharp movement of grinder may be
experienced.
Precautions to take when sanding paint
u
Sanding of lead based paint is NOT
RECOMMENDED due to the difficulty of
controlling the contaminated dust. The greatest
danger of lead poisoning is to children and
pregnant women.
u
Since it is difficult to identify whether or not a
paint contains lead without a chemical analysis,
we recommend the following precautions when
sanding any paint:
Personal safety
u
No children or pregnant women should enter
the work area where the paint sanding is being
done until all clean up is completed.
u
A dust mask or respirator should be worn by all
persons entering the work area. The filter
should be replaced daily or whenever the
wearer has difficulty breathing.
Содержание STCT1840
