background image

6

ENGLISH

Additional power tool safety warnings

 

Warning! Additional safety warnings 

for grinding, sanding, wire brushing, 

polishing or abrasive cutting-off opera-

tions.

u

 

This power tool is intended to function as a 

grinder, sander, wire brush, polisher or 

cut-off tool. Read all safety warnings, 

instructions, illustrations and speci-

fications provided with this power tool.

 

Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious 

injur.

u

 

  Operations for which the power tool was not 

designed may create a hazard and cause 

personal injury.

u

   

Do not use accessories which are not 

specificallydesigned and recommended by 

the tool manufacturer. 

Just because the 

accessory can be attached to your power tool, it 

does not assure safe operation.

u

  

 The rated speed of the accessory must be at 

least equal to the maximum speed marked 

on the power tool.  

Accessories running faster 

than their rated speed can break and fly apar.

u

   

The outside diameter and the thickness of 

your accessory must be within the capacity 

rating of your power tool. 

Incorrectly sized 

accessories cannot be adequately guarded or 

controlled.

u

  

 Threaded mounting of accessories must 

match the grinder spindle thread. For 

accessories mounted by flanges, the arbour 

hole of the accessory must fit thlocating 

diameter of the flange.

 Accessories that do 

not match the mounting hardware of the power 

tool will run out of balance, vibrate excessively 

and may cause loss of control.

u

   

Do not use a damaged accessory. Before 

each use inspect the accessory such as 

abrasive wheels for chips and cracks, 

backing pad for cracks, tear or excess wear, 

wire brush for loose or cracked wires. If 

power tool or accessory is dropped, inspect 

for damage or install an undamaged 

accessory. After inspecting and installing an 

accessory, position yourself and bystanders 

away from the plane of the rotating 

accessory and run the power tool at 

maximum no load speed for one minute. 

Damaged accessories will normally break apart 

during this test time.

u

   

Wear personal protective equipment. 

Depending on application, use face shield, 

safety goggles or safety glasses. As 

appropriate, wear dust mask, hearing 

protectors, gloves and workshop apron 

capable of stopping small abrasive or 

workpiece fragments. 

The eye protection 

must be capable of stopping flyingdebris 

generated by various operations. The dust 

mask or respirator must be capable of filtering 

particles generatedby your operation. 

Prolonged exposure to high intensity noise may 

cause hearing loss.

u

   

Keep bystanders a safe distance away from 

work area. Anyone entering the work area 

must wear personal protective equipment. 

Fragments of workpiece or of a broken 

accessory may fly away and cause injury 

beyondimmediate area of operation.

u

   

Hold power tool by insulated gripping 

surfaces only, when performing an 

operation where the cutting accessory may 

contact hidden wiring or its own cord. 

Cutting accessory contacting a “live” wire may 

make exposed metal parts of the power tool 

“live” and could give the operator an electric 

shock.

u

   

Position the cord clear of the spinning 

accessory. 

If you lose control, the cord may be 

cut or snagged and your hand or arm may be 

pulled into the spinning accessory.

u

   

Never lay the power tool down until the 

accessory has come to a complete stop. 

The 

spinning accessory may grab the surface and 

pull the power tool out of your control.

u

   

Do not run the power tool while carrying it 

at your side. 

Accidental contact with the 

spinning accessory could snag your clothing, 

pulling the accessory into your body.

u

   

Regularly clean the power tool’s air vents. 

The motor’s fan will draw the dust inside the 

housing and excessive accumulation of 

powdered metal may cause electrical hazards.

u

   

Do not operate the power tool near 

flammable materals. 

Sparks could ignite these 

materials.

u

   

Do not use accessories that require liquid 

coolants. 

Using water or other liquid coolants 

may result in electrocution or shock.

Содержание STCT1840





































Отзывы: