Stanley STCT1840, Руководство пользователя

Страница: 10 / 36

10
ENGLISH
being used ensuring no excessive play between
the accessory and the flanges.
Mounting
u
Place the inner flange (17) on the grinder
spindle (19) (fig.C1)
u
Place the wheel (6) against the flange. Screw
the threaded flange (18) onto the spindle (19).
(fig. C2).
u
Make sure that the threaded outer flange (18) is
facing in the correct direction for the type of disc
fitted. For grinding discs, the flange (18) is fitted
with the raised portion facing towards the disc
(fig. C3).
u
Press in the spindle lock button (4) and rotate
the spindle until it locks. Keeping the lock
button pressed in, tighten the threaded flange
(18) with the spanner (7) provided (fig. D)
Release the spindle lock.
Fitting and removing sanding backing
pads (fig. E & F)
For sanding, a backing pad is required. The back-
ing pad is available from your Stanley dealer as an
accessory.
Fitting
u
Place the inner flange (17) onto the spindle (19)
as shown (fig. F). Make sure that the flange is
correctly located on the flat sides of the inner
flange.
u
Place the backing pad (6) onto the spindle.
u
Place the outer sanding flange (18) onto the
spindle with the raised centre facing towards
the disc.
u
Keep the spindle lock (4) depressed and tighten
the outer flange using the two-pin spanner (7)
(fig. E). Make sure that the outer flange is fitted
correctly and that the disc is clamped tightly.
Removing
u
Keep the spindle lock (4) depressed and loosen
the outer flange (18) using the two-pin spanner
(15) (fig. E).
u
Remove the outer flange (18), the sanding disc
(16) and the backing pad (6).
Fitting and removing hubbed wheels
Hubbed wheels and cups install directly on the
M14 threaded spindle (19).
Caution! To reduce the risk of personal injury,
wear work gloves when handling wire brushes and
wheels. They can become sharp.
Caution! To reduce the risk of damage to the
tool, wheel must not touch guard when mounted
or while in use. Undetectable damage could occur
to the accessory, causing wires to fragment from
accessory wheel or cup.
Fitting
u
Thread the hubbed wheel or cup on to the
spindle (19) by hand.
u
Keep the spindle lock (4) depressed and tighten
the hub of the wheel or cup with a wrench.
Removing
u
Keep the spindle lock (4) depressed and loosen
the hub of the wheel or cup with a wrench.
u
Remove the wheel or cup from the spindle (19).
Fitting and removing the battery (fig. G)
u
To fit the battery (22), line it up with the
receptacle on the tool. Slide the battery into the
receptacle and push until the battery snaps into
place.
u
To remove the battery, push the release buttons
(23) while at the same time pulling the battery
out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not
overload.
u
Be prepared for a stream of sparks when the
grinding or cutting disc touches the workpiece.
u
Always position the tool in such a way that the
guard provides optimum protection from the
grinding or cutting disc.
Charging the battery (fig. A)
Warning
! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C. Recom-
mended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the
cell temperature is below approximately
0 °C or above 40 °C.The battery should be left in
the charger and the charger will begin to charge
automatically when the cell temperature warms up
or cools down.
u
To charge the battery (22), insert it into the
charger (21). The battery will only fit into the
charger in one way. Do not force. Be sure that